Are there any special practices to reboot a node in PPA?
So far a simple "shutdown -r now" hasn't broken anything but I want to make sure PPA doesn't make assumptions about the nodes being up at any point. (both management and service)...
We have one Cloud Server hardware node that exists only as the backup location for containers and VMs in Cloud Server/PVA (it hosts no virtual servers). Can it also serve as a Backup Server Node?
A related question, in my case, is whether we can configure a Backup Server Node to use a particular drive/mount/directory, as we can with PVA? I couldn't find any info in the docs about any settings at all for the Backup Server Node.
Any workaround for AWS and adding nodes for PPA. Since the AWS instances use key pairs for root access you can't ssh as root with a password.
View 3 Replies View RelatedWe are trying to add new service node but when we are trying to finish procedure we receive error: The usage of the resource "IP addresses" for subscription with ID "1" exceeds the value of "0".
We do not have a such subscription using ID "1". As I can see this is the ID in database for "Parallels Automation License Key", but it has unlimited license key and have already two nodes attached.
How to change IIS password after node is added to PPA using wizard..There is no option to change password after adding the service node.
View 2 Replies View Relatedit is possible to run services such as Apache, Mail, MySQL etc on the Management Node.
I have PBAS setup and have registered the PPA server with PBAS, the PPA Management Node is marked as ready to provide, I have added the appropriate attributes to the MN under Service Nodes, however according to PBAS I need to install the ppa_apache package (and probably others), and when I go to install the packages it's trying to install the ppa_agent package which is conflicting with ppa_core.
I have a problem to install a service node. In task, I have this error:
Unable to authenticate at the host '10.252.13.197'. To resolve this issue, please follow the instructions at [URL] ....
I followed the instructions, but mysql don't display my new server.
[root@plesk000-exp-01 ~]# mysql -uadmin -p`cat /etc/psa/.psa.shadow` psa -e 'select accessKey from ServiceNodes where ipAddress="10.252.13.197";'
[root@plesk000-exp-01 ~]#
I deleted service node but the problem still remains.
Due to data center limitations, I am restricted to 100GB on my primary disk but can have up to 2TB on a second disk.Is it possible to have the backup node use the second disk instead of the primary disk?Also is it possible to have multiple to have multiple backup nodes?
View 3 Replies View Relatedinstall such extension as Watchdog (available on PPP) on PPA Service nodes (or maybe as a Watchdog Server on Management node)?
View 2 Replies View RelatedI have some problems adding a database and a webserver service-node:
Mar 19 13:44:13 plesk-db : DBG [SYSTEM 4:6600:f6affb70 lib]: [SMConfig] {module_id="Common"; code="1"} Internal error: SAXParseException while parsing /usr/local/pem/etc/service_config.xml: element 'SERVICE_CONFIG' is not allowed for content model '(SERVICES)'.
Mar 19 13:45:50 plesk-www : DBG [SYSTEM 3:9054:f6affb70 lib]: [SMConfig] {module_id="Common"; code="1"} Internal error: SAXParseException while parsing /usr/local/pem/etc/service_config.xml: element 'SERVICE_CONFIG' is not allowed for content model '(SERVICES)'.
Content of the service_config.xml
Code:
<?xml version="1.0" encoding="UTF-8" standalone="no" ?>
<!DOCTYPE SERVICE_CONFIG PUBLIC "SM" "SM 1.0">
<SERVICE_CONFIG/>
We want to configure our PPA mail node to send all outbound mail through our spam filtering appliance but don't know where to start.
Reading standard Postfix docs give basic instructions on how to direct a handful of domains through a mail relay but we want to direct every outbound email from all domains through our spam filter.
We also want to ensure that any regular updates to the mail node won't break or undo this config.
I have a full mail node and I have to move some domains on a different node without losing data . Is possible with PPA?
View 3 Replies View Related im getting an error when im trying to create a subscription on a windows node via PPA management node, the task error is:
Method name: registerIpPlesk on SCREFleskWebIIS:0
Last execution output: This IP address XXX.XXX.XXX.XXX is already registered in Panel on the network interface Local Area Connection
the IP XXX.XXX.XXX.XXX is the correct service node IIS ip address..
Is it possible to update the MySQL version on the db nodes from 5.1 to 5.5 or is it supported?
View 3 Replies View RelatedWe have a PPA environment with 7 service nodes (one management node, two web-, two database- and two e-mail servers). We also have 2 variants of hosting, a consumer and business variant.
We want separate the consumers from the business variants on the service nodes.
I want to use webserver1, databaseserver1 and emailserver1 for consumer hosting and webserver2, databaseserver2 and emailserver2 for business hosting
I want to make two service templates, one consumer and one business template.
Is it possible to configure ppa : When we subscript a consumer template, everything must provision only on the consumer service nodes automatically (web01, db01 and email01) and not on the business services nodes.
I brought up a basic centos 6.5 install in desire to add it to my ppa cluster.
The ppa installation task failed because wget was missing on the new node. The error message made it easy to fix (yum install wget) but thought I'd report it so that your pre-req scripts can check and install it for future users.
I am trying to install Automation, and I keep getting an error after the "Getting SELinux" step, here is a log of the process so far:
Code:
[INFO]: Checking current user privileges...
[INFO]: Checking critical environment requirements...
[INFO]: Determining OS parameters...
[INFO]: Detected OS: CentOS-5-x86_64
[INFO]: Getting SELinux state...
[ERROR]: Unexpected error: ''
[Code] ....
I have tried running the installation on a different server and the same issue came up...
I am installing plesk automation on centos 6.5 using this command on a fresh system
./ppa_installer --password some_password --admin_email some_email
and get the following error.
[LOGTEE]: Error Downloading Packages:
[LOGTEE]:
[LOGTEE]: libuuid-2.17.2-12.18.el6.i686: failure: Packages/libuuid-2.17.2-12.18.el6.i686.rpm from base: [Errno 256] No more mirrors to try.
Looks like some lib is not found in the mirrors.
On a clean install of CentOS 6.6 (Final) I did the following:
1. updated the /etc/hosts file to point my ip to the hostname
2. Open the ports in the iptables file.
3. ran the ppa_installer per the instructions on [URL] ....
The ppa_installer log says installed Successfully. However the following occurs:
1. Cannot browse to the url:8443, or any of the other variations (8080, 8880, https/http)
2. Yum installer is now broken (I replicated this twice). Yum will not run at all with the following error:
There was a problem importing one of the Python modules required to run yum. The error leading to this problem was: /usr/lib64/libcurl.so.4: file too short
Please install a package which provides this module, or verify that the module is installed correctly.It's possible that the above module doesn't match the
current version of Python, which is:
2.6.6 (r266:84292, Jan 22 2014, 09:42:36)
[GCC 4.4.7 20120313 (Red Hat 4.4.7-4)]
I am now going to try Cent OS 6.4.. will report back.
After rebooting my server, my websites are no longer working.
If I access the plesk machine on the local network by it's hostname, the default Plesk page shows as expected. Everything on 8443 works too.
All hosted sites do not work. FTP DOES work. This seems limited to an http problem of some sort.
When trying to access the settings for mail on a domain I get the following error:
Error: Unable to find service node for ip address with id=6
I understand this is a problem with the database but I am not sure where to look to fix it.
I only have 4 IP addresses on the system.
I rebooted the srever
Code:
[root@server50 log]# date
Sun Jul 19 14:48:43 CDT 2009
[root@server50 log]# reboot
Broadcast message from root (pts/1) (Sun Jul 19 14:48:45 2009):
The system is going down for reboot NOW!
[root@server50 log]# uptime
14:49:02 up 47 days, 31 min, 1 user, load average: 0.07, 0.10, 0.09
[root@server50 log]# date
Sun Jul 19 14:58:11 CDT 2009
[root@server50 log]#
But server is not rebooting. Look like server need a hard reboot. Have anyonce faced this problem? why server is not rebooting?
I have a vps and I was having memory issues so I reboot my server. Upon doing that it seems to have put itself into a loop and is constantly rebooting itself every 5mins.
I checked the logs at /var/log/messages and found this:
Code:
(?@127.0.0.1) [INFO] Logout.
Jun 29 11:55:49 evercuben xinetd[24525]: EXIT: ftp status=255
pid=24296 duration=0(sec)
Jun 29 11:55:49 evercuben xinetd[24525]: EXIT: smtp status=1 pid=24292
duration=0(sec)
Jun 29 12:00:49 evercuben xinetd[24525]: START: smtp pid=1628 from=127.0.0.1
Jun 29 12:00:49 evercuben xinetd[24525]: START: ftp pid=1630 from=127.0.0.1
Jun 29 12:00:49 evercuben pure-ftpd: (?@127.0.0.1) [INFO] New
connection from 127.0.0.1
Jun 29 12:00:49 evercuben pure-ftpd: (?@127.0.0.1) [INFO] Logout.
Jun 29 12:00:49 evercuben xinetd[24525]: EXIT: ftp status=255 pid=1630
duration=0(sec)
Jun 29 12:00:49 evercuben xinetd[24525]: EXIT: smtp status=1 pid=1628
duration=0(sec)
Jun 29 12:05:49 evercuben xinetd[24525]: START: smtp pid=11347 from=127.0.0.1
Jun 29 12:05:49 evercuben pure-ftpd: (?@127.0.0.1) [INFO] New
connection from 127.0.0.1
Jun 29 12:05:49 evercuben xinetd[24525]: START: ftp pid=11349 from=127.0.0.1
Jun 29 12:05:49 evercuben pure-ftpd: (?@127.0.0.1) [INFO] Logout.
Jun 29 12:05:49 evercuben xinetd[24525]: EXIT: ftp status=255
pid=11349 duration=0(sec)
Jun 29 12:05:51 evercuben xinetd[24525]: EXIT: smtp status=1 pid=11347
duration=2(sec)
Jun 29 12:10:49 evercuben xinetd[24525]: START: smtp pid=20210 from=127.0.0.1
Jun 29 12:10:49 evercuben pure-ftpd: (?@127.0.0.1) [INFO] New
connection from 127.0.0.1
Jun 29 12:10:49 evercuben xinetd[24525]: START: ftp pid=20212 from=127.0.0.1
Jun 29 12:10:49 evercuben pure-ftpd: (?@127.0.0.1) [INFO] Logout.
Jun 29 12:10:49 evercuben xinetd[24525]: EXIT: ftp status=255
pid=20212 duration=0(sec)
Jun 29 12:10:49 evercuben xinetd[24525]: EXIT: smtp status=1 pid=20210
duration=0(sec)
Jun 29 12:15:49 evercuben xinetd[24525]: START: smtp pid=30100 from=127.0.0.1
Jun 29 12:15:49 evercuben pure-ftpd: (?@127.0.0.1) [INFO] New
connection from 127.0.0.1
Jun 29 12:15:49 evercuben xinetd[24525]: START: ftp pid=30102 from=127.0.0.1
Jun 29 12:15:49 evercuben pure-ftpd: (?@127.0.0.1) [INFO] Logout.
Jun 29 12:15:49 evercuben xinetd[24525]: EXIT: ftp status=255
pid=30102 duration=0(sec)
Jun 29 12:15:49 evercuben xinetd[24525]: EXIT: smtp status=1 pid=30100
duration=0(sec)
Jun 29 12:20:49 evercuben xinetd[24525]: START: smtp pid=7525 from=127.0.0.1
Jun 29 12:20:49 evercuben pure-ftpd: (?@127.0.0.1) [INFO] New
connection from 127.0.0.1
Jun 29 12:20:49 evercuben xinetd[24525]: START: ftp pid=7527 from=127.0.0.1
Jun 29 12:20:49 evercuben pure-ftpd: (?@127.0.0.1) [INFO] Logout.
Jun 29 12:20:49 evercuben xinetd[24525]: EXIT: ftp status=255 pid=7527
duration=0(sec)
i'm kinda desperate right now, I have an Ultra Sparc II with Solaris 8 but suddenly it start rebooting again and again by himself, after initialize memmory and starts booting, once the server displays the hostname it says that the server is coming down. and reboot all over again.
View 3 Replies View RelatedI have an Ultra Sparc II with Solaris 8 but suddenly it start rebooting again and again by himself, after initialize memmory and starts booting, once the server displays the hostname it says that the server is coming down. and reboot all over again.
View 0 Replies View RelatedI have a server that is monitored with a system that automatically reboots if a service appears to be down. The server is being rebooted several times a month and it seems to be getting more frequent.
The server load is almost never high. It's a dual Xeon with hyperthreading and the load is almost always below 1. Practically the only time it goes high is during cPanel backup and it hardly ever reboots during that.
The DC tried replacing the RAM, but a day and a half later it rebooted again.
The server has 1 fairly active MySQL message board and 3 fairly high bandwidth sites (images and video clips), and the rest of the sites are quite small and inactive. One thing the tech said was "Apache gets a lot of traffic so I'm not surprised to see an apache restart once a month or so. You have 115 concurrent connections to apache and over 25,000 hits in the last 2 hours alone" but I've gotten reboots a few times/week.
I suspect that my machine keep rebooting itself judging it's online for a while with the result of my ping that I can ping my machine for less than 3 minutes and then it goes offline afterward.
I've checked with the datacenter found my IP is clean and fine.
I have recently deployed PPA with on nodes with hostnames on the serverroom.net.au domain, so management.serverroom.net.au, mail.serverroom.net.au etc. The DNS is currently hosted on a plesk server which will soon be migrated to PPA.
When I add the serverroom.net.au domain to PPA, I it fails at the sync task with an error saying that there are no A or AAA records for ns1.serverroom.net.au, even when these records exist in the external DNS. The same error occurs when I try to add the domain as a dns entry and switch to internal...
i have installed a Win2008R2 server with IIS and Coldfusion. I want to allow customer to set DSN, i know that older "Plesk Panel" versions that can do but i missing this now in PPA in the customer view. In the subscription is OBDC and Coldfusion connections allowed and unlimited. Must i do anything to activate this ?
View 2 Replies View RelatedGot following Problem: Unable to find service node for web service on domain with id = 0
After a Check from [URL] ....
I tried this: [URL] ....
Result:
+--------------------+--------------+---------------------------------------+------------------------------+------------+
| Domains | Service Type | IpAddressesCollections.ipCollectionId | Current value of ipAddressId | Have to be |
+--------------------+--------------+---------------------------------------+------------------------------+------------+
| XXXXXXXXXXXXX.org | mail | 30 | 0 | 1 |
+--------------------+--------------+---------------------------------------+------------------------------+------------+
Resolution:
mysql -uadmin -p`cat /etc/psa/.psa.shadow` -Dpsa -e 'Update IpAddressesCollections SET ipAddressId = 1 WHERE ipCollectionId = 30'
Result: ERROR 1062 (23000) at line 1: Duplicate entry '30-0' for key 'PRIMARY'
Deleted a domain workspace in Parallels Plesk and now I am getting this error when signing into the panel:Looked at the logs and been trying multiple commands (including the bootstrapper repair etc.)I found the full error from the logs:
[13-Jun-2015 16:35:33 UTC] PleskDBException: Unable to find service node for web service on domain with id=6
file: /usr/local/psa/admin/plib/PhDomain.php
line: 1404
code: 0
trace: #0 /usr/local/psa/admin/plib/Smb/Subscription/Domain.php(490): PhDomain->getWebHostingServiceNode()
[code]....