Plesk Automation :: Cloud Server Hardware Node As Backup Server Node
Apr 11, 2015
We have one Cloud Server hardware node that exists only as the backup location for containers and VMs in Cloud Server/PVA (it hosts no virtual servers). Can it also serve as a Backup Server Node?
A related question, in my case, is whether we can configure a Backup Server Node to use a particular drive/mount/directory, as we can with PVA? I couldn't find any info in the docs about any settings at all for the Backup Server Node.
View 4 Replies
ADVERTISEMENT
Jun 10, 2015
Due to data center limitations, I am restricted to 100GB on my primary disk but can have up to 2TB on a second disk.Is it possible to have the backup node use the second disk instead of the primary disk?Also is it possible to have multiple to have multiple backup nodes?
View 3 Replies
View Related
Apr 1, 2014
I brought up a basic centos 6.5 install in desire to add it to my ppa cluster.
The ppa installation task failed because wget was missing on the new node. The error message made it easy to fix (yum install wget) but thought I'd report it so that your pre-req scripts can check and install it for future users.
View 3 Replies
View Related
Sep 4, 2014
Any workaround for AWS and adding nodes for PPA. Since the AWS instances use key pairs for root access you can't ssh as root with a password.
View 3 Replies
View Related
May 16, 2014
We are trying to add new service node but when we are trying to finish procedure we receive error: The usage of the resource "IP addresses" for subscription with ID "1" exceeds the value of "0".
We do not have a such subscription using ID "1". As I can see this is the ID in database for "Parallels Automation License Key", but it has unlimited license key and have already two nodes attached.
View 4 Replies
View Related
Jun 4, 2014
Are there any special practices to reboot a node in PPA?
So far a simple "shutdown -r now" hasn't broken anything but I want to make sure PPA doesn't make assumptions about the nodes being up at any point. (both management and service)...
View 1 Replies
View Related
Feb 18, 2014
How to change IIS password after node is added to PPA using wizard..There is no option to change password after adding the service node.
View 2 Replies
View Related
Mar 18, 2014
it is possible to run services such as Apache, Mail, MySQL etc on the Management Node.
I have PBAS setup and have registered the PPA server with PBAS, the PPA Management Node is marked as ready to provide, I have added the appropriate attributes to the MN under Service Nodes, however according to PBAS I need to install the ppa_apache package (and probably others), and when I go to install the packages it's trying to install the ppa_agent package which is conflicting with ppa_core.
View 2 Replies
View Related
Jun 15, 2015
I have a problem to install a service node. In task, I have this error:
Unable to authenticate at the host '10.252.13.197'. To resolve this issue, please follow the instructions at [URL] ....
I followed the instructions, but mysql don't display my new server.
[root@plesk000-exp-01 ~]# mysql -uadmin -p`cat /etc/psa/.psa.shadow` psa -e 'select accessKey from ServiceNodes where ipAddress="10.252.13.197";'
[root@plesk000-exp-01 ~]#
I deleted service node but the problem still remains.
View 1 Replies
View Related
Apr 24, 2014
install such extension as Watchdog (available on PPP) on PPA Service nodes (or maybe as a Watchdog Server on Management node)?
View 2 Replies
View Related
Mar 19, 2014
I have some problems adding a database and a webserver service-node:
Mar 19 13:44:13 plesk-db : DBG [SYSTEM 4:6600:f6affb70 lib]: [SMConfig] {module_id="Common"; code="1"} Internal error: SAXParseException while parsing /usr/local/pem/etc/service_config.xml: element 'SERVICE_CONFIG' is not allowed for content model '(SERVICES)'.
Mar 19 13:45:50 plesk-www : DBG [SYSTEM 3:9054:f6affb70 lib]: [SMConfig] {module_id="Common"; code="1"} Internal error: SAXParseException while parsing /usr/local/pem/etc/service_config.xml: element 'SERVICE_CONFIG' is not allowed for content model '(SERVICES)'.
Content of the service_config.xml
Code:
<?xml version="1.0" encoding="UTF-8" standalone="no" ?>
<!DOCTYPE SERVICE_CONFIG PUBLIC "SM" "SM 1.0">
<SERVICE_CONFIG/>
View 3 Replies
View Related
May 20, 2014
We want to configure our PPA mail node to send all outbound mail through our spam filtering appliance but don't know where to start.
Reading standard Postfix docs give basic instructions on how to direct a handful of domains through a mail relay but we want to direct every outbound email from all domains through our spam filter.
We also want to ensure that any regular updates to the mail node won't break or undo this config.
View 2 Replies
View Related
May 14, 2015
I have a full mail node and I have to move some domains on a different node without losing data . Is possible with PPA?
View 3 Replies
View Related
Apr 10, 2014
im getting an error when im trying to create a subscription on a windows node via PPA management node, the task error is:
Method name: registerIpPlesk on SCREFleskWebIIS:0
Last execution output: This IP address XXX.XXX.XXX.XXX is already registered in Panel on the network interface Local Area Connection
the IP XXX.XXX.XXX.XXX is the correct service node IIS ip address..
View 1 Replies
View Related
Jun 6, 2015
Is it possible to update the MySQL version on the db nodes from 5.1 to 5.5 or is it supported?
View 3 Replies
View Related
Aug 11, 2014
We have a PPA environment with 7 service nodes (one management node, two web-, two database- and two e-mail servers). We also have 2 variants of hosting, a consumer and business variant.
We want separate the consumers from the business variants on the service nodes.
I want to use webserver1, databaseserver1 and emailserver1 for consumer hosting and webserver2, databaseserver2 and emailserver2 for business hosting
I want to make two service templates, one consumer and one business template.
Is it possible to configure ppa : When we subscript a consumer template, everything must provision only on the consumer service nodes automatically (web01, db01 and email01) and not on the business services nodes.
View 4 Replies
View Related
Apr 9, 2014
I'm in the process of installing PPA on infrastructure running Parallels Cloud Server. Each container has 2 interfaces, one public facing and a private interface for inter-server communication.
No problems installing PPA 11.5 (specifying IP's on commandline) or adding service nodes however, the firewall rules the documentation speaks of are nowhere to be seen? i.e.:
Important: After the installation, PPA creates the special firewall chain PPA-SN-Rules-INPUT used for communication with service nodes. Do not change it, otherwise, you will not be able to add service nodes to PPA.Click to expand...
Has this been dropped from PPA 11.5 ? (I recall seeing the firewall settings in 11.1) There is also no sign of the ppa.firewall tool that is also mentioned.
The only rule I see inserted is for Postgres on the management node, and 2 for pleskd on all of the nodes (open to world!).
View 2 Replies
View Related
May 29, 2009
I have a lot of experience with VPSs and recently have been working with dedicated servers but my partner and I are going to be providing VPSs and my main concern is securing the node the VPSs will be on. Would I secure it like a normal dedicated server?
I'm worried that if I secured it like I would my dedicated servers it would affect the VPS clients hosted on there. Any assistance is appreciated, even if it's just a recommendation for a management company or single user who could assist us.
View 7 Replies
View Related
May 8, 2014
It has been bought to my attention during our upgrade planning, that PPA & Plesk Panel do not offer the functionality for setting up a backup MX servers. In our current configuration we use Sendmail as both secondary and tertiary MX servers. These are manually configured and prone to configuration mistakes.
Multiple scenarios need to be taken into consideration.
Scenario 1: Hosters Plesk hosted primary mail server + secondary & tertiary mail servers.
Scenario 2: Client hosted primary mail server + hosters secondary & tertiary mail servers.
I am looking for alternate ways for backup / secondary MX servers for our planned PPA / Plesk deployment. An automated solution would be ideal, but we are falling short trying to find a solution to streamline the process and remove margin for error.
View 1 Replies
View Related
Jun 30, 2014
When trying to access the settings for mail on a domain I get the following error:
Error: Unable to find service node for ip address with id=6
I understand this is a problem with the database but I am not sure where to look to fix it.
I only have 4 IP addresses on the system.
View 2 Replies
View Related
Sep 10, 2014
Got following Problem: Unable to find service node for web service on domain with id = 0
After a Check from [URL] ....
I tried this: [URL] ....
Result:
+--------------------+--------------+---------------------------------------+------------------------------+------------+
| Domains | Service Type | IpAddressesCollections.ipCollectionId | Current value of ipAddressId | Have to be |
+--------------------+--------------+---------------------------------------+------------------------------+------------+
| XXXXXXXXXXXXX.org | mail | 30 | 0 | 1 |
+--------------------+--------------+---------------------------------------+------------------------------+------------+
Resolution:
mysql -uadmin -p`cat /etc/psa/.psa.shadow` -Dpsa -e 'Update IpAddressesCollections SET ipAddressId = 1 WHERE ipCollectionId = 30'
Result: ERROR 1062 (23000) at line 1: Duplicate entry '30-0' for key 'PRIMARY'
View 16 Replies
View Related
Jun 24, 2015
Deleted a domain workspace in Parallels Plesk and now I am getting this error when signing into the panel:Looked at the logs and been trying multiple commands (including the bootstrapper repair etc.)I found the full error from the logs:
[13-Jun-2015 16:35:33 UTC] PleskDBException: Unable to find service node for web service on domain with id=6
file: /usr/local/psa/admin/plib/PhDomain.php
line: 1404
code: 0
trace: #0 /usr/local/psa/admin/plib/Smb/Subscription/Domain.php(490): PhDomain->getWebHostingServiceNode()
[code]....
View 1 Replies
View Related
Jun 15, 2014
Clean install on openSUSE 13.1
After deleting a domain, we got the following error which rendered the panel useless.
Internal error: Unable to find service node for web service on domain with id=5
Message Unable to find service node for web service on domain with id=5
File PhDomain.php
Line 1402
Type PleskDBException
Go To Previous Page
View 6 Replies
View Related
Nov 7, 2009
i'm a vps provider and i'm using this server for vps host
Code:
Dual CPU Xeon 5420, 24GB Ram, 1TB HDD
24GB of Ram
and now i see the used ram is un normal
Code:
[root@216-19-200-162 ~]# free -m
total used free shared buffers cached
Mem: 24064 23865 199 0 541 19509
-/+ buffers/cache: 3813 20251
Swap: 4094 0 4094
[root@216-18-201-162 ~]#
the free ram us 199 of 24GB!
every time when i reboot the server the used ram back normal but after per hours the issues back again
i have contacted the DC and they say that there is no problem with there hardware
the number of vpses in that node is 7 and all the vps have a limit ram.
View 14 Replies
View Related
Mar 6, 2009
I want to build a VPS Node using Quad Socket Tyan Motherboards and AMD Opteron 2376 Shanghai 2.3 GHz Processor (Quad Core).
I am in doubt since I notice that some providers (at least two rather big provider which I have account) are using Dual Core AMD Opteron 2212.
Is there any specific reason why those providers is not using 2376 AMD Processors? .. is it because the Dual Core AMD Opteron 2212 supports Virtualization Technology, while the 2376 is not?
I will use Xen Hypervisor, usually I use Intel 54xx Processors but looking for *cheaper* solution , so I am really new in AMD Base Server.
View 3 Replies
View Related
Oct 22, 2009
I build raid10 for VPS nodes. Now, I will use SAN, so all VPS will be created in SAN. With the host server, I assume that I don't need fast disk array, because all the disk requests have been processed in SAN already?
View 4 Replies
View Related
Oct 18, 2009
For a quad core processor with 16-32GB RAM and SAS raid 10, would 30 VPS's be a lot?
I have a VPS with 1Gb RAM on a machine as above. I'm running about 40 (relatively low-volume) websites on it. Seems to me that if 30 others were doing anything similar, that would overwhelm a single machine.
Am I just making an uninformed bad assumption? So far, performance on my VPS has been fine.
View 14 Replies
View Related
Mar 6, 2009
Well the age old question for virtual servers, would you rather a host put all his eggs into one basket "monster node" or several smaller ones. From a provider standpoint one server is easier to manage than several, although if that one goes down, all your customers do with it. Lower costs for the provider, s/he can then pass the savings along.
Example Package:"2GB Ram Packages, 500GB bandwidth, and 20GB space."
The "EXAMPLE" Specs.
All in one
Max Clients: 126
4U Rackmount,
4 Quad Cores, "16 total cores"
256GB DDR2,
8 600GB SAS 10k,
RAID10
Several Server setup:
Max Clients: 14
1U Rackmounts,
Single Quad Core, "4 cores"
32GB DDR2,
2 300GB SAS 10k,
RAID1
If you could tell me why you picked either or.
View 14 Replies
View Related
Oct 16, 2009
i have a very high load in my node every time i monitor the load i see load average: 8.19 and some times it's go up to 60 - 80
i'm using this server
Intel Core2Quad Q9650
Ram 8GB
Bandwidth: 10000gb
Hypervm Control Panel
and there is only 6 vpses ....
View 7 Replies
View Related
Jun 19, 2009
i'm using hypervm/openvz
and i have the main package of ips which i have received from datacenter
i orderd other package ips (13) ips
i have add them to ip pools in hypervm and it didn't working
Note : netmask are different for the first ips and the second ips
when i create vps i can't login and when i ping ip it didn't ping ( requested timed out )
i have one server from softlayer and the other from limestonenetworks
when i order additonal ips from softlayer it works proberly .. now when i orderd those ips from limestonenetworks ; i think it must be modified manually
View 14 Replies
View Related
Apr 14, 2009
i have node 16 cpu AMD 64 gb ram HDD sas 15 with raid 10 /hypervm + openvz i host 10 vps
my problem when any vps load go over 2 the Node load go to 30 - 40 some time 100 i set CPU UNITS , Number Of CPUS and Cpu Usage for every vps but the load in node is go up
how i can set limit in vps and prevent from effect on load Node?
View 2 Replies
View Related
