Plesk 11.x / Linux :: Parallel Panel Not Working On 8443 Port
Jun 18, 2014My plesk panel is not working on 8443 Port.
It is giving error like server not found.
My plesk panel is not working on 8443 Port.
It is giving error like server not found.
How change control panel url port (8443 to 9859)?
View 15 Replies View RelatedI have a Windows VPS with Plesk panel. Windows Server 2008 R2 with plesk panel version 11.5.30.
I tried to change the default plesk panel port (8443) to eg (1234) without any success.
The steps i followed are the following:
1) Firewall -> Inbound rule -> allow for port 1234
2) Firewall, Disable inbound rule for port 8443
3) IIS, PleskControlPanel, Bindings: changed binding from 8443 to 1234.
Now i type on browser: [URL] .... and while its loading after some seconds redirects me to [URL] ...
I need to access plesk 11.0 over a subdomain at port 80 rather than port 8443 as my office firewall blocks the port 8443.
I tried KB article [URL] .... but its not working.
E.g.: I would like to access plesk panel @ portal.example.com rather than @ example.com/8443or8880
I have ample of spare IPs to use it...
I have been using managed servers for all of my webhosting career. I just decided to try to do it all on my own and of course, here come the growing pains.
I went with Linode for my new hosting provider. I followed their guides to get the initial setup done, minus setting up MariaDB.
I then went ahead and installed Plesk 12. The install went off without a hitch. But, now that I try to hit my hostname:8443, I get a 404.
I have done the following in an attempt to resolve the issue:
- Restart the server
- Restart the sw-cp-server
- Remove the /etc/sw-cp-server/conf.d/agent.conf (which didn't exist)
I do have the following firewalld rules in place:
firewall-cmd --zone=public--add-port=8443/tcp --permanent
firewall-cmd --zone=public--add-port=8447/tcp --permanent
I was wondering if it is possible to disable plesk redirect for clients domains on port 8443.I do not not want clients to to be able to access the plesk login screen when they visit exampleclientdomain.com:8443 but obviously i still want to be able to access my control panel e.g. myprimarydomain.com:8443. Is there something i can do to prevent the sites redirecting to my primary domain or am i better creating a htaccess rule to stop/redirect traffic on port 8443 ?
View 2 Replies View RelatedI want redirect Plesk port 8443 from non-ssl to ssl. What should I do?
I use Plesk 11 Windows.
Example: http://domain.com:8443 redirect to https://domain.com:8443
I have a server which I am using for multiple clients. Some with SSL enabled, some without. I have added custom ngingx conf files for nginxDomainVirtualHost.php and nginxWebmailPartial.php in /usr/local/psa/admin/conf/templates/custom and modified the following lines to try and harden security:
Code:
ssl_protocols TLSv1 TLSv1.1 TLSv1.2;
ssl_ciphers "EECDH+ECDSA+AESGCM EECDH+aRSA+AESGCM EECDH+ECDSA+SHA384 EECDH+ECDSA+SHA256 EECDH+aRSA+SHA384 EECDH+aRSA+SHA256 EECDH+aRSA+RC4 EECDH EDH+aRSA RC4 !aNULL !eNULL !LOW !3DES !MD5 !EXP !PSK !SRP !DSS";
ssl_prefer_server_ciphers on;
After reconfiguring using
Code:
/usr/local/psa/admin/bin/httpdmng --reconfigure-all
I check in /etc/nginx/plesk.conf.d/vhosts/<domain>.conf and the changes are shown correctly there but browsers and online tools such as [URL] .... still say that the sites are using 128 bit encryption and TLS 1.0.
The Plesk admin panel itself displays 256 bit encryption and TLS 1.2.
Mail Statistic not working, In /var/log/maillog contains below logs:The limit on the number of allowed outgoing messages was exceeded. Try again later.
But on Home
>
Tools & Settings
>
Outgoing Mail Control
Attempts to send mail per hour (except the current hour):
Statistics are being calculated.Count statistic not working, it not show any infomation abount mail attempt sending. !When i check ./mailserver -i options
POP3 authorization: off
SMTP authorization: on
Maximum letter size: 20971520
Relaying: auth
Check the passwords in the dictionary: on
Enable MAPS spam protection: off
MAPS zones: b.barracudacentral.org;zen.spamhaus.org
Short POP3/IMAP mail account names: off
The maximum number of connections (IMAP, POP3, IMAP over SSL, or POP3 over SSL).: 1024
[code]....
Show the alert on the Home page about attempts to exceed limits based on statistics for the last: P1DSend a notification about attempts to exceed limits on outgoing mail every: PT15M
How can I allow only one ip or a list of ip addresses to access port 8443.I need to limit access this port to few ip addresses and not everyone
View 6 Replies View Relatedto configure helm panel on these points
1) Domain Expire notification
2) Exceed Domain web space notification
I was creating an Plesk extension and I need to edit root's crontab for the extension to work properly. While doing some experiment I understand that the Plesk extension works with the permission of psaadm . So I cannot use shell_exec to do this. Is there any api or cli interface where I will be able to do this. Is there any possibility to override the restriction of psaadm user through extension.
View 4 Replies View RelatedI would like to know how to change http://mydomainname.com:8880 to http://mydomainname.com/somethingelse?
View 4 Replies View RelatedWe have tried to add branding to our Plesk Automation install but are not having any luck.
When trying to access the branded domain it tries to redirect to https://branded-domain.com but the page fails to load, looks as though the control panel is not listening on port 443.
Even trying to access https://ip-address of CP fails but https://ip-address:8443 works fine.
If I try to telnet to the CP ip:443 it fails to connect.
After Plesk panel upgrade to 12.x webadmin stopped working . It's showing following error
Code:
Server Error in '/' Application.
The resource cannot be found.
Description: HTTP 404. The resource you are looking for (or one of its dependencies) could have been removed, had its name changed, or is temporarily unavailable. review the following URL and make sure that it is spelled correctly.
What steps do I need to take to uninstall Parallel Plesk 11 for Windows. Then Reinstall Parallel Plesk 11 for Windows. Because my "File Manager" got corrupted, my download link timesout and I need this fixed.
View 5 Replies View RelatedI have an office internal website and I opened a port in the gateway of my office (7080) to this website (server )'s 80 port. That makes this website open to public as office has static IP. And then when I view the site from home . it's fine. But when I tried to login, the site is using a pop-up, I guess it's http authentciation, login, I was redirected to a url without my port number any more, that stops my access to the site as obviously I would.
How can I keep my connection/port number ...?
installing a softarwe that used port 8088, but that port is used by plesk. What ports not used by plesk and how do I assigned one to this new software.
server Centos 5 +
I have 2 IPs for my vServer. Plesk automatically add both addresses to the Plesk Panel. One of the ip address I want to use for another service (openvpn). The Problem is, that i can't delete the IP from the Plesk panel.
I got the message: Fehler: String was provided for unescaped parameter host.
There are no reseller or customers who use this IP. So how can i solve this problem and delete the IP from the Panel?
Using Plesk 12.0.18
I want to upgrade to Plesk 12, but want to make sure current version of 11.5.30 is working properly.Whenever Plesk tried to update I get the following error.Installing packages
Loaded plugins: fastestmirror, priorities, refresh-packagekit
Loading mirror speeds from cached hostfile
* atomic: www5.atomicorp.com
* epel: mirror.compevo.com
437 packages excluded due to repository priority protections
[code]....
Fatal error during packages installation: The GPG keys listed for the "CentOS / Red Hat Enterprise Linux 6 - atomicrocketturtle.com" repository are already installed but they are not correct for this package.Check that the correct key URLs are configured for this repository. YumBaseError: The GPG keys listed for the "CentOS / Red Hat Enterprise Linux 6 - atomicrocketturtle.com" repository are already installed but they are not correct for this package. Check that the correct key URLs are configured for this repository.
ERROR: Failed to run the Yum utility.The Yum utility failed to install the required packages.
Does Plesk's own server, "sw-cp-server" use a different PHP binary than is used for hosted sites?I've found the .ini, /usr/local/psa/admin/conf/, but I can't figure out where the binary would be? I'm trying to run some WP-CLI commands, but some functions I have disabled in the default PHP.ini are required by WP-CLI.
View 2 Replies View RelatedI have several clients still using WinXP. How do I disable SNI for SSL certificates ( and just use old IP way )?
View 18 Replies View RelatedAfter having some issues with my server mail program i read an article online where i though removing psa-courier-imap will resolve my mail problems.
Now nor my email is working but also i lost my plesk panel. Going to plesk ip address there's nothing anymore.Checked my server and is printing i have plesk 11.0.9 installed but is nowhere to find. I try to install psa-courier-imap again but yum cant find it.
Everything working on the server including all sites are available on the web.The only think i'm missing is the Plesk login page.
ERROR: Zend_Db_Statement_Exception: SQLSTATE[HY000]:
General error: 126 Incorrect key file for table '/tmp/#sql_50f_0.MYI'; try to repair it (Pdo.php:234)
After upgrading to v12 i have no access to the plesk panel. The message above is shown.
Each migration in the last years I'm running into this bug that Postfix wants to run on port 587 even though this is turned OFF in the Plesk Panel.
Sometimes it does this after some update.
Because another process is running on port 587 this means that postfix does not start and I have some downtime until I "repair" this.
"Repairing" means going into Plesk panel and turning ON SMTP-Auth.... Wait a moment for it to apply and then turning it OFF again....
This unwanted behaviour can be easily reproduced by having this option turned off in the Plesk panel and then running /usr/local/psa/admin/sbin/mchk --without-spam
This will end up in a non-running postfix if another process is already running on port 587.
This shouldn't be happening. Especially because I reported this behaviour years ago..
I would like to close port 25 and use other port for SMTP service and so avoid a lot of attempts to Access my SNTP port.
I followed all the steps in [URL] ... included the last one, about close port 25 from external.
And now qmail can send mails but can not receive from external senders. Is there any solution for solve it? or qmail must listen port 25?
I need changing the nginx port. I've followed various threads and have created a custom nginxDomainVirtualHost.php file at: /usr/local/psa/admin/conf/templates/custom/domain, while the website indeed moves to the port I have set, a second nginx thread starts at port 80 and takes over in it's place.
I need to put varnish at port 80 and cannot do so until all services relinquish control on port 80.
Followed clues here: [URL] ....
some here: [URL] .....
Turn's out to be able to change the nginx port to a non-standard port you need to edit 6 files
nginx.php
nginxDomainForwarding.php
nginxDomainForwardingIpDefault.php
nginxDomainVhost.php
nginxDomainVhostIpDefault.php
nginxWebmail.php
For the time being i disabled SSL support for my test domain as I didn't need it. The line you need to look for the in above files is:
Code:
$VAR->server->nginx->httpPort
So the line would finally become from this:
Code:
<?php echo $VAR->includeTemplate('server/nginxVhosts.php', array(
'ssl' => false,
'frontendPort' => $VAR->server->nginx->httpPort,
'backendPort' => $VAR->server->webserver->httpPort,
)) ?>
to this:
Code:
<?php echo $VAR->includeTemplate('server/nginxVhosts.php', array(
'ssl' => false,
'frontendPort' => "8888",
'backendPort' => $VAR->server->webserver->httpPort,
)) ?>
To get this to work you'll need to create a custom directory at: /usr/local/psa/admin/conf/templates
And copy the files over from the root of /usr/local/psa/admin/conf/templates/default
I just created a new Domain "bernhardlinz.de" at the
Plesk Panel -> Websites & Domains -> Add new Domain
After the Creation the new Domain does not appear under "Websites & Domains".
I check the domain with
Code:
/usr/local/psa/bin/domain -i bernhardlinz.de
And all looks fine like my other, older domains:
Code:
General
=============================
Domain name: bernhardlinz.de
Owner's contact name: Bernhard Linz (admin)
Domain status: OK
[Code] ....
I can see the domain under "Mails" and also create new mail accounts. There are no Errors for this under
Code:
/usr/local/psa/admin/logs/panel.log
As i try to add the domain first i got a
Code:
[11-Jul-2014 21:41:35 Europe/Berlin] PleskUtilException: mailmng-outgoing failed: ERROR:outgoing:database disk image is malformed
Which I removed with the
Code:
/usr/local/psa/admin/sbin/mchk
Command I found in the Plesk forum. After that i could add the domain.
I try a add another fantasy domain - also works but alos not displaying in Panel "Websites & Domains"
I take a look at the Plesk-Database "psa" with the Build-In "phpMyAdmin"
I take a look at the table "domains" and it looks like the other entries.
The Server was restored a few days before from a Backup. After the restore i had have the problem the "mysql" service did not start. I fixed the problem with the description from [URL] ... (Start mysql in recoverymode, export all data, delete the content of the whole mysql folder /var/lib/mysql folder, init new database and import the exported data). After that all looks fine.
Following the update from 11 to Plesk 12 (and installing latest Ubuntu fixes), the Plesk panel access is broken. Welcome page says:Can not load key: key is empty.And of course, no way to login the mgt interface. All services appear up, so this is only affecting the panel web service.
Fishing out the panel.log, it appears to be at a lower level than I initially thought (see below): experiencing issues after updating from 11 to 12 on Ubuntu (12)?
[18-May-2015 19:46:34 Europe/Berlin] PHP Warning: file_get_contents(/opt/psa/var/sso.sp.pem): failed to open stream: No such file or directory; File: /opt/psa/admin/externals/xmlseclibs.php, Line: 285
[18-May-2015 19:46:34 Europe/Berlin] Exception: PHP Warning: file_get_contents(/opt/psa/var/sso.sp.pem): failed to open stream: No such file or directory; File: /opt/psa/admin/externals/xmlseclibs.php, Line: 285
file: /opt/psa/admin/plib/Smb/Exception/Syntax.php
line: 56
[code]..
PRODUCT, VERSION, MICROUPDATE, OPERATING SYSTEM, ARCHITECTURE
11.5.30 Update #44, Ubuntu precise 64bit
PROBLEM DESCRIPTION
Upgrade fails with message: Failed to update Panel.you can send the update log to Parallels support. View the update logs (May 22, 2014). Copy the logs to your computer before you close this message.