We setup a new server and we're trying to use virtual() function to work with a certain script that requires it.
We already tried several ways to make it work. But at this moment, we only could make it work on PHP 4 with DSO.
After migrating from the old ensim to the new "X", everything is working fine, except for the webalizer, I activated webalizer in one domain a few days ago.. and everyday Im trying to see the webalizer information, and it is always displaying this message:
Could not retrieve the requested site report because the Web server logs have not yet been generated. These are generated once a day. Please check again later.
I also tried forcing the log rotating for that site, but the problem still there.
Server is RHES 4 with EnsimPro X, log generation and webalizer is activated for the domain.
I configured monit to send me email alerts when apache is using too many resources but I cannot receive email alerts. I use Qmail.
As for syslog, there is this message:
monit[6473]: Sendmail: error receiving data from the mailserver 'localhost' -- Resource temporarily unavailable
I tried to add for server name the name used in MX record but with the same result.
Btw: other things configured in cron (eg. RKHUNTER) send me alerts OK.
im using centos and a perl script doesnt seem to work on my system.
it gives an error on this line.
use LWP::UserAgent;
$ua = LWP::UserAgent->new;
$ua->agent("MyApp/0.1 ");
BEGIN failed--compilation aborted at line 8.
is it a problem with my perl or is it an error with the script?
I'm on windows vista. I've got an SDSL line into the house with a dedicated IP 62.etc. I've then got a Prestige 791R and all PC's plugged in to that. I've also got a wireless router for my Wii set up.
Basically I've set up this DHCP thingy to start at 192.etc.3 and the Wireless router is at 192.etc.1 and the Prestige is at 192.etc.2 my pc is at 192.etc.9
This is about where my knowledge stops unfortunately.
I have installed apache as the most basic default install I think you can and it seems to be working absolutely fine. I'm assuming I could also install PHP and MySQL etc and wouldn't have too much of a problem, however, my friend cannot seem to access the environment from the WAN IP and when I type in my WAN IP I get the prestige router's control panel.
I read somewhere that I needed to forward port 80, now I can 'open' ports in the prestige control panel but I did try opening port 80 in the control panel and pointing it to my LAN IP (92.etc.9) but it didn't seem to work.
I'm at a bit of a loss so if anyone could point me in the right direction I would be most grateful, just to clarify:
//localhost loads the html file 100%
//192.etc.9 loads the html file 100%
//62.WANIP internally loads my prestige routers control panel
//62.WANIP externally does not load a page (cannot be found)
If you need any more info just let me know and I'll get it.
I have a remote XP PC: 172.16.1.5 OpenVPN connection with route added for 192.168.2.0/24 to go via the VPN
Now on the other end the network consists of:
I have a OpenVPN server inside the lan on 192.168.2.245
Its default gateway is 192.168.2.1
I have 3 Windows Servers, 192.168.2.246, 247 and 248. All gateways are set to 192.168.2.1.
I have a ethernet router on the network, 192.168.2.1, it has a route added for 192.168.0.0/16 to go via 192.168.2.245, and route added for 172.16.0.0/24 to go via 192.168.2.245 also). the 192.168.0.0/16 is incase any other LANs are connected at a later date, if computers saw any packets not on the the 192.168.2.x subnet they would be routed to the default gateway which would then pass them to the OpenVPN router.
The trouble is, i can remotely connect and ping to the OpenVPN router fine and also the ethernet router, however when i ping any of the Windows boxes it times out. But i can open up Remote Desktop and connect to the windows box without problem, infact if i am running 'ping 192.168.2.246 -t' it will suddenly come alive but only after the RDP connection is made.
Is this something funny with the routing? I want to keep the OpenVPN server internal to the network and i appreciate it is hitting the ethernet router then being passed to the OpenVPN but something is weird as it fires up RDP fine but not ping. No firewalls are enabled on any of the boxes. If i log into ssh on the OpenVPN router or ethernet router i can ping from that to the windows boxes fine.
Its as if a ICMP redirect is issued, and all is well after the 1st connection. Not too sure but could anyone be kind enough to enlighten me?
My server which runs cPanel (license issued touchsupport) is having problems with handling emails.
I use an external DNS provider (editdns.net) only for this 1 particular domain for handling many Records and such. Through their panel, I have added my mail server's record, i.e. "mailserver.tld".
Now there is a problem with one part of the email issue. I have email piping setup and 1 webmail account setup too. These two work flawlessly. No issues with them. But email forwarding and default address doesn't work.
I am confident that the email settings are working right because, when my clients send an email, piping works and my support system creates a new ticket. But the email forwarding/Default EMail doesn't.
Not just that, I cannot even connect to the webmail account I created via POP3. I 100% sure that I used the correct login credentials and also tried the "+" and ":" for the username part. Just doesn't work. But I can access and read my emails via the Webmail (squirrelmail).
Please help me out with this as soon as possible.
the php mail function not work on my server!
when I run this function not show any error too.
for example I run this code:
<?php
echo "ok";
$to = 'myemail@mydomain.com';
$subject = 'the subject';
$message = 'hello';
$headers = 'From: test@domainname.com' . "
" .
'Reply-To:test@test@domainname.com' . "
" .
'X-Mailer: PHP/' . phpversion();
if(mail($to, $subject, $message, $headers)){
echo "sent";
}else{
echo "notsent";
}
?>
I just re-installed PHP4, Apache, and MySQL and now the "mail" function in PHP will not work. Is there a way to correct this? Is there some configuration value in Apache or PHP I must change?
View 2 Replies View RelatedPHP Mail Function not work and i cant fix it :/
i dont know whats the problem, but php.ini is right.
i also test email-function here: [URL]
I'm experiencing some issue with the php function mail(). No mails can get out and no errors from php. Is there any menu where we can parameter this php function ? Do I need to check up some services ?
CentOS 6.5 with Plesk 11.5
Fresh install
since my Update up to plesk 12
at the moment none of my websites can send E-Mails via sendmail :-(
OS: RHEL 6.4
SELinux: permissive mode
Apache: 2.2, mod_fcgid, mod_suxec, mod_ssl enabled
Common Name: [URL] .....
As posted in a previous thread I noted how I have been hosting with GeekStorage. After a little bit of investigation I found that a total of 593 (possibly more) website where being hosted on the same server as mine. I'm not sure if this is overselling but because I'm new to all this but I'm pretty sure it is.
Now, I'm looking on switching from GeekStorage to someone who doesn't oversell. I would be fine with 10-20GB of storage and >150GB bandwidth. Budget is 5-10$ a month.
so for over 3 weeks now pc-core.net had some problems with their servers and my accounts were just lost and no one answers my support tickets they just erase them, they disabled my account to support so i can only submit support tickets and click the link on the email.
they told me to email cshelpdesk.com to get my account moved to a new server and cshelpdesk is just telling me im SOL. they dont have access to the server i was at and basically to F off.
is there anything i can do? im basically just being ignored and they dont even have a number to them.
my forum is VB and its doesnt sent any email for users!
i check the options and everything looks fine ..
my vps had csf firewall installed ..
the csf.conf is
# Lists of ports in the following comma separated lists can be added using a
# colon (e.g. 30000:35000).
# Allow incoming TCP ports
TCP_IN = "53,1116,80"
# Allow outgoing TCP ports
TCP_OUT = "53,80,3306,1116"
# Allow incoming UDP ports
UDP_IN = "1116,53"
# Allow outgoing UDP ports
# To allow outgoing traceroute add 33434:33523 to this list
UDP_OUT = "53,1116"
# Allow incoming PING
ICMP_IN = "0"
# Set the per IP address incoming ICMP packet rate
# To disable rate limiting set to "0"
ICMP_IN_RATE = "1/s"
# Allow outgoing PING
ICMP_OUT = "1"
# Set the per IP address outgoing ICMP packet rate
# To disable rate limiting set to "0"
ICMP_OUT_RATE = "1/s"
and the version of csf is
[root@www csf]# /usr/sbin/csf -v
csf: v4.56 (generic)
[root@www csf]#
am useing centOS5 and ssh port 1116
am not useing any of control panel or ftp ...
the email i configured it with google.com/a services ..
my sys admin is currently in vacation and ovh staff cant help me much so i really appreciate if someone could help me tackle down this issue. I cant create ftp account at all heres what ovh said
Good morning,
Thank you to trust us, there is not my point of view or that of my colleague problem of the kernel compilation on your server or a file corrupted, and your Apache web server is functional, Status of the launch; after this command, via ssh:
/ etc / init.d / httpd start
Starting httpd: [OK]
We see that the port is open 80:
netstat-tanpu | grep 80
tcp 0 0 0.0.0.0:7080 0.0.0.0: * LISTEN 3071/lshttpd
tcp 0 0 0.0.0.0:80 0.0.0.0: * LISTEN 14349/httpd
From the outside, at this precise moment, we are able to establish a connection on port 80:
Telnet ks357687.kimsufi.com 80
Trying 91.121.148.X ...
Connected to ks357687.kimsufi.com.
Escape character is'^]'.
Get
<! DOCTYPE HTML PUBLIC "- / / IETF / / DTD HTML 2.0 / / EN">
<html> <head>
<title> 501 Method Not Implemented </ title>
</ head> <body>
<h1> Method Not Implemented </ h1>
<p> get to / not supported. <br />
</ p>
<hr>
<address> Apache/2.2.8 (EL) Server at ks357687.kimsufi.com Port 80 </ address>
</ body> </ html>
Connection closed by foreign host.
If I stop the Apache server:
/ etc / init.d / httpd stop
Stopping httpd: [OK]
More than 80 active port or connection possible from the outside:
In this case the connection of the exterior evidemment is not possible:
Telnet ks357687.kimsufi.com 80
Trying 91.121.148.X ...
telnet: Unable to connect to remote host: Connection refused
I am using Windows 2003 Enterprise Edition SP1 and i have recently set the computer up to 4GB RAM. I notice a problem occur error :
When I start the computer, Bios detected all 4GB Ram. However, i have checked Total physical memory in General (My Computer-> Properties) doesnot detect all 4GB Ram. it only detect 3GB Ram.
I have checked that this OS support up to 32GB . Why it doesn't detect all 4GB ?
What happen to it?
Mainboard : Intel chipset 915GL
I did following the instruction in internet (exactly is Microsoft) is /PAE in boot.ini file. But, it doesnt work.
Yesterday we registerd and created 2 domains in our server.
Everything is ok, files uploaded, dns zones created, httpd virtual host created...
The problem is that trying to browse the site trough http://www.site.com redirects me to [url] my main server IP address, this page shows a cPanel Welcome message.
But, using [url], the site is loaded ok, withouth any problems.
DNS zone shows:
Code:
; cPanel 11.11.0-BETA_16977
; Zone file for site.com
$TTL 14400
@ 86400 IN SOA mydns1.wolo.com. admin.hostingserver.com. (
2007092601 ; serial, todays date+todays
86400 ; refresh, seconds
7200 ; retry, seconds
3600000 ; expire, seconds
86400 ) ; minimum, seconds
site.com. 86400 IN NS mydns1.wolo.com.
site.com. 86400 IN NS mydns2.wolo.com.
site.com. IN A IP_ADDRESS
localhost.site.com. IN A 127.0.0.1
site.com. IN MX 0 site.com.
mail IN CNAME site.com.
www IN A IP_ADDRESS
ftp IN A IP_ADDRESS
Apache virtual host code
Code:
<VirtualHost IP_ADDRESS>
ServerAlias www.site.com
ServerAdmin webmaster@site.com
DocumentRoot /home/siteuser/public_html
ServerName site.com
<IfModule mod_suphp.c>
suPHP_UserGroup siteuser siteuser
</IfModule>
<IfModule mod_php4.c>
php_admin_value open_basedir "/home/siteuser:/usr/lib/php:/usr/local/lib/php:/tmp"
</IfModule>
<IfModule mod_php5.c>
php_admin_value open_basedir "/home/siteuser:/usr/lib/php:/usr/local/lib/php:/tmp"
</IfModule>
User siteuser
Group siteuser
BytesLog /usr/local/apache/domlogs/site.com-bytes_log
CustomLog /usr/local/apache/domlogs/site.com combined
Options -ExecCGI -Includes
</VirtualHost>
The email of my client doesnt receive certain emails from certain accounts, including my yahoo.com.ph account. After several tries I received this error instead.
After trying to send mail unsuccedfully several times, this is the error I am getting.
Hi. This is the qmail-send program at yahoo.com.
I'm afraid I wasn't able to deliver your message to the following
addresses.
This is a permanent error; I've given up. Sorry it didn't work out.
:
Sorry, I couldn't find any host by that name. (#4.1.2)
I'm not going to try again; this message has been in the queue too
long.
--- Below this line is a copy of the message.
Quote:
Originally Posted by copy of email
Return-Path:
Received: (qmail 90296 invoked by uid 60001); 25 Jun 2007 04:05:27
-0000
DomainKey-Signature: a=rsa-sha1; q=dns; c=nofws;
s=s1024; d=yahoo.com;
h=X-YMail-OSG:Receivedate:Fromubject:To:MIME-Version:Content-Type:Content-Transfer-Encoding:Message-ID;
b=GYMZ4utbLEJMc+EXHdW5Ng5ZJeCArXAubpEaUtZzZz77STh9HAGNhrFDjgfqNJ5BdE/
SAlCQ78wseeWPTqUFlalE246OSls0L2tnadTvmxHAQiALfIJ/efHw980subD/VVk6c3NZXGKaKn3vQwJ57bHW5a6qsWjazjl6BXp5Q20=;
X-YMail-OSG:
1iaqBZkVM1mfqTKSQPqhJwf61.zXtBuozzwn.p275yXXF_KgFA8taeSyThc.P1xawEKTuVIB
Vgxk18AHBp_TxSZD753CsOSTbU56JD1OgWwBl8GCwZNxI6YhJHPfyg--
Received: from [203.177.91.252] by web32604.mail.mud.yahoo.com via
HTTP; Sun, 24 Jun 2007 21:05:26 PDT
Date: Sun, 24 Jun 2007 21:05:26 -0700 (PDT)
From: *********
Subject: test
To: sales@*********.com
MIME-Version: 1.0
Content-Type: multipart/alternative;
boundary="0-357102911-1182744326=:89673"
Content-Transfer-Encoding: 8bit
Message-ID: <979097.89673.qm@web32604.mail.mud.yahoo.com>
--0-357102911-1182744326=:89673
Content-Type: text/plain; charset=iso-8859-1
Content-Transfer-Encoding: 8bit
test
to upload some flash videos over to our web host.
All the videos have been uploaded to << link removed >> and in there you will seea flash_video directory, in there should be a html file where you can double click and watch the flash video.
Now go ahead and try it, click on the HTML file and click CONTINUE and try clicking on MODULE 1.. You will see a video play to the left but on the right are bunch of POWERPOINT slides that will appear as the guy continues to speak. THAT DOESNT SHOW..
Our website is hosted by xo.com
Dont know much about the plan since its my 2nd day at the job..
But here is the weird part,
i have uploaded the samething - same exact way to another web host and it plays fine, the PPTs show up fine..
What do you guys think it is?
Before someone asks about uploading methods, i tried filezilla, coreftp and cuteFTP using both ASCII and binary methods. Samething..
It possible to disable the disable function for all user expect one account for running few application i need shell_exec, passthru, exec these so for other account it possible to disable it?
View 2 Replies View Relatedsuppose that i am a costumer. is it possible to see disabled function in php.ini?
(using any script)
How can figure out which functions are active on my server?
I have root access and the server is Linux.
I want to know wheather the function "fsockopen" is open or not.
Fatal error: Call to undefined function: curl_init() in /home/user/public_html/news/include/function.php on line 1526
how to fix this.??
thanks
NB: My server info
Centos
apache1
my php -v give :
Code:
php -v
PHP 4.4.7 (cli) (built: Jul 27 2007 18:31:31)
Copyright (c) 1997-2007 The PHP Group
Zend Engine v1.3.0, Copyright (c) 1998-2004 Zend Technologies
with the ionCube PHP Loader v3.1.31, Copyright (c) 2002-2007, by ionCube Ltd., and
with Zend Extension Manager v1.2.0, Copyright (c) 2003-2007, by Zend Technologies
with Suhosin v0.9.20, Copyright (c) 2002-2006, by Hardened-PHP Project
with Zend Optimizer v3.3.0, Copyright (c) 1998-2007, by Zend Technologies
I got this warning message from a script I was working on to read XML feeds.
Warning: file_get_contents(url) [function.file-get-contents]: failed to open stream: A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond. in C:Apache2.2htdocs est5.php on line 8
but when i run the url itself, it works fine.
i already set allow_url_fopen = On
I am starting to webhosting company in it I have included a package will be free and add supported and also I want to disable some functions like mail() ..........I mean I want to disable SMTP services anyone have idea how can I do that.
View 14 Replies View RelatedCan anyone tell me in order to use the crypt function (amd md5sum) in a c++ program (g++ on CentOS assuming the cryptography libary is installed) what do I have to
#include
?
I got PHP working. But some of the Ajax functions it not working.
For example:
in wordpress admin, i can only use HTML mode to start a new post. I cant switch to VISUAL mode. And it was working before though.
What option do i need to compile PHP with to make it work?
Right now i have:
Quote:
'./configure' '--prefix=/opt/lsws/lsphp4' '--with-litespeed' '--with-mysql' '--with-gd' '--enable-shmop' '--enable-track-vars' '--enable-sockets' '--enable-sysvsem' '--enable-sysvshm' '--enable-magic-quotes' '--enable-mbstring' '--without-pear' '--with-bz2' '--with-curl' '--with-exec-dir=/usr/bin' '--with-freetype-dir=/usr' '--with-png-dir=/usr' '--enable-gd-native-ttf' '--without-gdbm' '--with-gettext' '--with-gmp' '--with-iconv' '--with-jpeg-dir=/usr' '--with-openssl' '--with-png' '--with-pspell' '--with-expat-dir=/usr' '--with-pcre-regex=/usr' '--with-zlib'
I have just changed servers and uploaded a mail() script which was working on my previous config but does not work on the new server config. What is stopping the emails from being delivered, is there something new in WHM that I need to do?
Here are my WHM and cPanel details:
WHM 11.11.0 cPanel 11.15.0-R18264
REDHAT 4 i686 on standard - WHM X v3.1.0
I have mixed feelings on the mail() function in php. I've seen it send out amazing numbers of emails and yet I keep reading that it is prone to problems. I'm wondering if someone can put an approximation on what you could/would send out in say 60 seconds. I know that there are tonnes of variables, so i'll try and remove a few:
- server hardware is typical of a cpanel/WHM shared hosting environment
- running apache/linux
- email is say 20kb HTML format
- mail is sent in a php script loop, one by one; alternatively, mail() could be called in clusters of x emails - like send 5 emails at once
- there are 400 recipients