i have a Centos server that install Xen and hypervm in it.
i have some vps in this server.
i restart server and after that i get this eror for run vps :
Could Not Start Vps, Reason: Error: Device 0 (vif) could not be connected. Could not find bridge, and none was specified:
how can i solved this problem ?
my server is : Centos5.2
im still getting the following error
Code:
root@main [/tmp/apf-9.7-1]# ./install.sh
Installing APF 9.7-1: eth0: error fetching interface information: Device not found
Completed.
Installation Details:
Install path: /etc/apf/
Config path: /etc/apf/conf.apf
Executable path: /usr/local/sbin/apf
Other Details:
eth0: error fetching interface information: Device not found
cp: cannot stat `/etc/apf.bk.last/vnet/*.rules': No such file or directory
Imported options from 9.7-1 to 9.7-1.
Note: Please review /etc/apf/conf.apf for consistency, install default backed up to /etc/apf/conf.apf.orig
my host has said
Code:
edit the apf.conf file to venet0:0 instead of eth0
which ive done and im still getting the error, Ive pasted my current conf.apf config below
Code:
#!/bin/sh
#
# APF 9.7 [apf@r-fx.org]
# Copyright (C) 1999-2007, R-fx Networks <proj@r-fx.org>
# Copyright (C) 2007, Ryan MacDonald <ryan@r-fx.org>
# This program may be freely redistributed under the terms of the GNU GPL
#
# NOTE: This file should be edited with word/line wrapping off,
# if your using pico/nano please start it with the -w switch
# (e.g: pico -w filename)
# NOTE: All options in this file are integer values unless otherwise
# indicated. This means value of 0 = disabled and 1 = enabled.
##
# [Main]
##
# !!! Do not leave set to (1) !!!
# When set to enabled; 5 minute cronjob is set to stop the firewall. Set
# this off (0) when firewall is determined to be operating as desired.
DEVEL_MODE="1"
# The installation path of APF; this can be changed but it is not recommended.
INSTALL_PATH="/etc/apf"
# Untrusted Network interface(s); all traffic on defined interface will be
# subject to all firewall rules. This should be your internet exposed
# interfaces. Only one interface is accepted for each value.
IFACE_IN="venet0"
IFACE_OUT="venet0"
# Trusted Network interface(s); all traffic on defined interface(s) will by-pass
# ALL firewall rules, format is white space or comma separated list.
IFACE_TRUSTED=""
# This option will allow for all status events to be displayed in real time on
# the console as you use the firewall. Typically, APF used to operate silent
# with all logging piped to $LOG_APF. The use of this option will not disable
# the standard log file displayed by apf --status but rather compliment it.
SET_VERBOSE="1"
# The fast load feature makes use of the iptables-save/restore facilities to do
# a snapshot save of the current firewall rules on an APF stop then when APF is
# instructed to start again it will restore the snapshot. This feature allows
# APF to load hundreds of rules back into the firewall without the need to
# regenerate every firewall entry.
# Note: a) if system uptime is below 5 minutes, the snapshot is expired
# b) if snapshot age exceeds 12 hours, the snapshot is expired
# c) if conf or a .rule has changed since last load, snapshot is expired
# d) if it is your first run of APF since install, snapshot is generated
# - an expired snapshot means APF will do a full start rule-by-rule
SET_FASTLOAD="0"
I was just upgrading my system packages using up2date, and got this error...:
Code:
Testing package set / solving RPM inter-dependencies...
########################################
libpng-1.2.2-27.i386.rpm: ########################## Done.
libpng-devel-1.2.2-27.i386. ########################## Done.
libpng10-1.0.13-17.i386.rpm ########################## Done.
libpng10-devel-1.0.13-17.i3 ########################## Done.
rh-postgresql-7.3.19-1.i386 ########################## Done.
rh-postgresql-devel-7.3.19- ########################## Done.
rh-postgresql-libs-7.3.19-1 ########################## Done.
rh-postgresql-python-7.3.19 ########################## Done.
rh-postgresql-server-7.3.19 ########################## Done.
samba-3.0.9-1.3E.13.2.i386. There was some sort of I/O error: [Errno 28] No space left on device
But I do have space on all my partitions...
Also installing only the samba package it fails:
Code:
Testing package set / solving RPM inter-dependencies...
########################################
samba-3.0.9-1.3E.13.2.i386. There was some sort of I/O error: [Errno 28] No space left on device
im using RHEL 3 + cPanel.
i have a problem when i wget anyfile after i install
APF+BFD into my server
my server is VPS ..
my VPS details is
---------------------
Server Name: bOx
User Name: b0x
Operating System: CentOS 5
RAM: 512 MB Guaranteed 2 GB BurstedTotal
Disk Space: 10 GB
Bandwidth Quota: 500 GB
Quota Used: 0 GB
Control Panel Type: cPanel (license enabled)
Server IP Address: 72.152.456.37
---------------------
now my VPS when i restart my APF its show me this
eth0: error fetching interface information: Device not found
eth0: error fetching interface information: Device not found
and my SSH Froze in this ..
kernel: EXT3-fs error (device loop0): ext3_lookup: unlinked inode 12286 in dir #2
kernel: EXT3-fs error (device loop0): ext3_journal_start_sb: Detected aborted journal
EXT3-fs error (device loop0): ext3_lookup: unlinked inode 12286 in dir #2
I have installed CSF on my VPS and when I try and start it I get, anyone know what going on and how to fix it, or pass info on to my host.
iptables: Unknown error 18446744073709551615
LOG tcp opt -- in * out * 0.0.0.0/0 -> 0.0.0.0/0 limit: avg 30/min burst 5 LOG flags 0 level 4 prefix `Firewall: *TCP_IN Blocked* '
Error: iptables command [/sbin/iptables -v -A LOGDROPIN -p tcp -m limit --limit 30/m --limit-burst 5 -j LOG --log-prefix 'Firewall: *TCP_IN Blocked* '] failed, at line 211
Full ready out
Restarting csf...
Flushing chain `INPUT'
Flushing chain `FORWARD'
Flushing chain `OUTPUT'
Restarting bandmin acctboth chains for cPanel
ACCEPT all opt -- in lo out * 0.0.0.0/0 -> 0.0.0.0/0
ACCEPT all opt -- in * out lo 0.0.0.0/0 -> 0.0.0.0/0
DROP tcp opt -- in * out * 0.0.0.0/0 -> 0.0.0.0/0 tcp dpt:67
DROP udp opt -- in * out * 0.0.0.0/0 -> 0.0.0.0/0 udp dpt:67
DROP tcp opt -- in * out * 0.0.0.0/0 -> 0.0.0.0/0 tcp dpt:68
DROP udp opt -- in * out * 0.0.0.0/0 -> 0.0.0.0/0 udp dpt:68
DROP tcp opt -- in * out * 0.0.0.0/0 -> 0.0.0.0/0 tcp dpt:111
DROP udp opt -- in * out * 0.0.0.0/0 -> 0.0.0.0/0 udp dpt:111
DROP tcp opt -- in * out * 0.0.0.0/0 -> 0.0.0.0/0 tcp dpt:113
DROP udp opt -- in * out * 0.0.0.0/0 -> 0.0.0.0/0 udp dpt:113
DROP tcp opt -- in * out * 0.0.0.0/0 -> 0.0.0.0/0 tcp dpts:135:139
DROP udp opt -- in * out * 0.0.0.0/0 -> 0.0.0.0/0 udp dpts:135:139
DROP tcp opt -- in * out * 0.0.0.0/0 -> 0.0.0.0/0 tcp dpt:445
DROP udp opt -- in * out * 0.0.0.0/0 -> 0.0.0.0/0 udp dpt:445
DROP tcp opt -- in * out * 0.0.0.0/0 -> 0.0.0.0/0 tcp dpt:513
DROP udp opt -- in * out * 0.0.0.0/0 -> 0.0.0.0/0 udp dpt:513
DROP tcp opt -- in * out * 0.0.0.0/0 -> 0.0.0.0/0 tcp dpt:520
DROP udp opt -- in * out * 0.0.0.0/0 -> 0.0.0.0/0 udp dpt:520
iptables: Unknown error 18446744073709551615
LOG tcp opt -- in * out * 0.0.0.0/0 -> 0.0.0.0/0 limit: avg 30/min burst 5 LOG flags 0 level 4 prefix `Firewall: *TCP_IN Blocked* '
Error: iptables command [/sbin/iptables -v -A LOGDROPIN -p tcp -m limit --limit 30/m --limit-burst 5 -j LOG --log-prefix 'Firewall: *TCP_IN Blocked* '] failed, at line 211
...Done.
Restarting lfd...
Stopping lfd:[ OK ]
[ OK ]
Starting lfd:[ OK ]
...Done.
I have a perplexing error that I can't figure out. I'm running a server using Sun Web Server 7 and PHP 5.x, and have been doing so since late October 2007. Now, just recently - in the past month and a half - I've seen an exponential increase in server 500 errors, specifically "stub start" errors. Google has very little at all to return on stub start errors, and looking into the Sun documentation has been fruitless too. So i'm wondering if anyone here has any experience with such errors or can give me any tips on what to try next. The weird thing is that the 500 errors tend to happen in spikes - 5,000 of them will happen within a 10 minute span, and then back down to normal levels.
View 0 Replies View RelatedI just installed mySQL server on a brand new dedicated server and am getting Timeout error occurred trying to start MySQL Daemon. I have uninstalled and reinstalled it a few times and am still getting the same error.
View 11 Replies View RelatedI am getting the error (as listed in the title) on my server. This is a BRAND NEW FRESH install on a brand new server...
OS: Unix Fedora
Kernel Version: Kernel 2.6.18-1/2798.fc6 on an i686
Hardware Information: Brand new Dell SC1435 Server
Software Version: MySQl 5
Control Panel: Nothing yet
Apache starts ok but when I go to strart MySQL I get the following error...
[root@server112]# /etc/rc.d/init.d/mysqld start
Timeout error occurred trying to start MySQL Daemon
Starting MySQL: [FAILED]
Does anyone have any ideas?
I did some pretty extensive searching...
Web Hosting Talk article that basically describes the same error. I followed everything as listed in his suggestion and it didn't change anything.
Also Checked here but this didn't work either.
httpd server configuring.I share my files only from local disks but some of my resources are located on truecrypt secure volume.When I want to start my server now I have to mount my all drives first to have all path active. Otherwise httpd doesn't start with 'invalid path' error.My question is, how to force httpd starting without path or drive exists checking?
Platform Windows7 x64
Apache version 2.4.3
Package Xampp
I think someone from a single ip abusing my service.
is there anyway to check number of conenction per ip?
so that i ban the ip with max number of connection.
Is there a way where i can view which IP connected to my server the most? I need to find out if there is certain IP keep hitting my mail server until it crashed.
Preferably the software could sort out the highest hit IP then to the lowest.
[url]
If you look at the image there are 14 connections from a blank ip what is that and how do i stop it?
I have a Windows Server with Virtual Server 2003 R2. I also have a Windows Server 2003 Enterprise virtual server on the box, this is more of a test. I have 4 IP's on the box, so I decided to use one that I don't normally use. I set it up exactly like my host network is setup, and I start it up. It's connected, has the IP, but it's not transferring any packets, but it seems to be connected.
View 7 Replies View RelatedThis worked yesterday.
Now I get connect: No route to host when I try to FTP.
What to do?
I can ping the IP without problems.
Is London Hosting Centre in any way connected to BlueSquare 1, 2 or 3 in connection terms, for example with BlueSquare went down would London Hosting Centre still be up etc...
As I am wanting to setup a backup site.
I've tried the uptime ssh command but that only shows how many users are currently connected to the server via ssh. Does anyone know a command to show how many active http connections there are? I'll use php to run the command and print it to the users browser so they can see how many users are on each server. Very similar to what gamershell do.
View 9 Replies View RelatedI administer an Apache server under unix environment SunOS 5.10,I want to know the number of clients connected to my apache server
View 7 Replies View RelatedI'm looking for information about having EXTERNAL ms-sql 2008/2012 servers with MS-SQL Web Edition license connected to one or more Plesk servers.
We don't want to use the Express version coming with Plesk but use MS-SQL 2008 & 2012 (both accessible by clients if possible), on individual dedicated machines for SQL only.Of course we'd like to have all current functionality coming with Plesk Power Panel inc. backup/restore options from within Plesk.
Is there a reason to set a high TTL for DNS? Like the standard is a few days.I set mine to 10 minutes. So whenever I do a change its propagated within 10 minutes. Is there a reason this would be bad? I realize it means more queries to my server, but 10 minutes is still rather long, not like thats going to totally hammer my server,
View 7 Replies View RelatedWe currently have a server that has Windows 2003 and were wondering the advantages of upgrading to R2? How I spend the extra money for an upgrade? Please no linux comments
View 11 Replies View RelatedI took server from Soft Layer
After four month they banned my account, When I talked to them they said we banned your account for tow days because we Suspicion about you and I waited them for tow days but nothing new, after that I sent all my evidences to them, the passport picture, driver's license, ID's card and Visa Card picture from front and back.
NOW!
I don't know the reason for banned my account, why they banned me?
today 3ix.com logged into my ftp account and delete some files! i thought the site is hacked but the truth my site didn't hacked ! when i asked the support team to allow me to change my ftp details from the client area he said to me " Help24x7: Well, we got complaint from SpamCop against your site and we are unable to host it "
this problem was solved long time ago and spamcup register here in the forum and said to all " im sorry the report was false" ! then 3ix.com restord my account again , why they now open this old problem!
look here at the problem you will finde the full details
[url]
and here the hostcare admin said to me we are sorry the report was false ! we are going to restore your account " We just got confirmation from SpamCop that they feel the complaint was false and I have asked a 3iX Admin to restore your site, it will be live in the next 60 minutes.
Thank you for working with us to resolve the issue, don't hesitate to contact the 3iX HelpDesk if you have any further difficulties.
Regards "
[url]
im very wondering ! why they open this olde proble again! they wast my time and mak me very sad.
dose this justice?
here is also another person they treminate his account please read
[url]
my server was down today and i want to know the reason can you please help me by pointing out the log files i should check?
Am runing CentOS 4.x with many domains on the server,
ip addr add 69.39.**.**/29 dev vmnet0
iam getting cant find the device vmnet0
how to add it
Has anyone here ran the CSF firewall on a bridged networking device?
View 1 Replies View RelatedI have a dual processor, dual core server with 12GB memory.. It uses less than 4% CPU utilization and less than 5% memory utilization, but for some reason It's really slow to load sites...
I know this isn't much information, but would any have any ideas as to what could cause the slow speed?
If is anyone is available to look at it, I'll pay you (obviously).
I'm having my first DDOS attack. Do people DDos servers for no reason? Beacause they are attacking an IP on a server that have not had any sites or any use on it for 4 years.
View 4 Replies View RelatedI can not find anything weird on the server.
Everything seems normal.
Why the traffic go high suddenly, then it drop to normal after a while.