I'm having a problem with my /usr. When I check it through WHM it's 100% full. But when I check it through SSH ( du -sh /usr ). it's almost 50% full
is there a way to let WHM recalculates the disk usage for /usr.
i already tried to empty it. but the 100% in WHM never changed. I deleted about 3GB of files. but in WHM, still saying 9.4GB used from 9.9GB
I'm running Plesk 12.0.18 on Centos 7, recently I've got emails from backup service stating that it could not complete the backup due to insufficient space available on disk. Normally I have plenty of disk space available so I check the disk using the command
df -h
Filesystem Size Used Avail Use% Mounted on
/dev/root 20G 2.3G 17G 13% /
/dev/md2 91G 82G 4.4G 95% /var
it seems that /var has been growing up a lot,
but if I run the command
du -sh /var
I get a total size of 5.7G (not 82G as stated before)
is Plesk calculating the wrong size or it's me using the wrong commands?
I have noticed a weird thing lately with two VPS accounts. Virtuozzo's system usage meter on the Resources page creeps up to 100% over the course of 24 hours or so and stays there, but stays green and I don't get any QoS alerts. The servers both seem to be running fine, and I haven't had any crashes. One VPS is running a few Wordpress blogs.
The other is running some Joomla sites.
Both are running Virtuozzo on CentOS 4.7 i686 with WHM 11.24.2 and cPanel 11.24.4-R32486.
In the past, when the system usage meter in Virtuozzo got anywhere near 100%, it turned yellow or red, I had sites go down, and all kinds of QoS alerts for privmpages were thrown. It turned out back then that I had a bad PHP script eating tons of memory with too many MySQL queries. That doesn't appear to be the case here, since I'm not having any apparent problems with either server. It seems like a "non-problem" but it has me concerned because I'm used to using that system usage meter in Virtuozzo to keep an eye on the health of the VPS..
When I look at memory used in WHM (WHM->Server Status->Server Status) it shows only 31% used, which is what I used to see in Virtuozzo.
When I run free, I get:
root@server [~]# free
total used free shared buffers cached
Mem: 524288 133804 390484 0 0 0
-/+ buffers/cache: 133804 390484
Swap: 0 0 0
When I run Free, I get:
root@server [~]# Free
Memory limit...: 8388604 MB (burstable: 8388604 MB)
Current usage..: 120 MB (0%) (requested: 264 MB)
Free memory....: 8388484 MB (100%)
Initially, I suspected it was another problem with MySQL, and restarting MySQL does drop the system usage meter down to ~31% in Virtuozzo for a while--without changing the actual memory used on the System Processes page--but the memory usage for MySQL with Virtuozzo pegged is only 6.23% in WHM.
Here's the really weird thing: If I look at Virtuozzo->System Processes it shows only 0.4% (I think they mean 40%) of total memory used, half of which is mysqld and the rest is spamd.
With no sign of problems, it looks like Virtuozzo is incorrectly reporting memory usage in the system usage meter, but correctly in the system processes list.
The web host's response was:
We use SLM for managing VPSes. This enforces your per VPS limits and doesn't let your VPS use more then it should be. It sounds like you guys may have some memory hogs in your applications.
Have you guys considered cutting down some of the unneeded plugins and stuff?
That doesn't make any sense to me given the disparity between the memory usage meter and the amount of memory usage reported in System Processes and with free/Free as well as the lack of QoS alerts, but maybe SLM prevents any alerts? I don't want to let a memory hog run free on my system if one exists.
i Have 2 vps From Swvps and HostForWeb
When Finish Transfer Old VPS( HostForWeb ) To New VPS (Swvps.com) and See Disk Usage
Swvps=> 13 gig Usage
HostForWeb=> 23 gig space!
I am getting problem , my package is 500MB and i have checked cpanel > file manager , there is showing disk usage 350 MB but there is no file under public_html/ and out of public_html/ directory , what can i do and why this is showing 350 MB disk usage but there is no files.
View 9 Replies View Relatedwhm only shows this in server information area > disk usage
Code:
Filesystem Size Used Avail Use% Mounted on
/usr/tmpDSK 243M 4.4M 226M 2% /tmp
/tmp 243M 4.4M 226M 2% /var/tmp
It is not showing actual disk space for sda1/sdb1
I restarted crond and that did not fix it, nor forced cpanel update.
I recently had to do an OS reload on my server box and when i restored all the accounts, they are all viewing as using 0mb of space.
View 7 Replies View Relatedmy vps virtuozzo indicates that my disk usage is full. However, my only 1 site is using only a few gig.
what should i do? what folder should i safely delete to free up some space?
etc, dev? or maybe tmp?
root@server # df -h
Filesystem Size Used Avail Use% Mounted on
/dev/sda3 145G 145G 0 100% /
/dev/sda1 99M 41M 54M 44% /boot
none 250M 0 250M 0% /dev/shm
/usr/tmpDSK 6.7G 74M 6.3G 2% /tmp
/tmp 6.7G 74M 6.3G 2% /var/tmp]
I cannot trace where the usage is coming from. There is only one account on this box using 26GB. Its a centos/cpanel box. I checked /var/log and had already deleted audit.d directory. /usr/local/apache/domlogs and logs show almost nothing.
Running the latest version of WHM 11.23.2 & cPanel 11.23.4-C26138
So far tried the following commands:
/scripts/initquotas
/scripts/resetquotas
/scripts/fixquotas
the above commands done nothing - really waste of time!
The cPanel asked my to contact my VPS provider and ask them to reinitialize quotas for your VE and possibly check further into the node to correct the issue. As for VPS provider they did some tests & told me that they "fixed" & can't find any issues on the node, but the problem is still exists.
asked by VPS provider to do:
/scripts/fixquotas
restart VPS
/scripts/upcp --force
how to fix cPanel bug?
The attached image are proof of Disk usage not being updated in WHM & cPanel, as this account contains 17.6 MB (18,472,960 bytes).
When I check hard disk usage I get the following:
Quote:
Filesystem Size Used Avail Use% Mounted on
/dev/sda2 9.7G 8.4G 905M 91% /
/dev/sda5 215G 415M 204G 1% /var
/dev/sda1 99M 16M 78M 17% /boot
tmpfs 2.0G 0 2.0G 0% /dev/shm
/dev/sdb1 227G 188M 215G 1% /disk1
sda2 is 91% used.. I am not sure what is it filled with. How can I know what is exactly on that partition?
I'm starting a webhosting business in the next few months (working on the panel), and was wondering what is the best method to limit the amount of disk usage the user can use? I know about Disk Quota, but that would be a pain to use. Is there anything built into IIS7?
Also, is it possible to use a SQL 05 DB for FTP user accounts with IIS7? If not, is there any other way to have FTP accounts *without* having to create a windows user account?
I have been a Plesk Panel user for several years and I found PPA very interesting because of its great scalability.
It has been time consuming to figure it out how PPA handles several Plesk Panel aspects.
Does PPA has support for MailEnable disk usage calculation? If it does, where? and how often does it collect disk usage info from Mail Service Node??
[openvz] WHM not show partition on Service Status and Disk usage
Hi, the VPS not show the partition on "Service Status" of WHM and in the "Show Current Disk Usage" see the Attach Files images...
How to fix/show this?
Attached Thumbnails
ÂÂ*
today i get a vps from lime, and i try to create a vps
but when i try to enable vps i get this message :
Could Not Start Vps, Reason: vzquota : (error) Quota getstat syscall for id 110: Inappropriate ioctl for device: vzquota init failed [3]:
and the disk usage not display properly:
I'm on PPA 11.5 MU#2 (Should upgrade to MU#3 soon). My problem is that the Usage of Disk Space for all my customers subscriptions are not calculated. I've run the daily maintenance script (which it actually runs periodically), but there's no update on the display.
View 3 Replies View RelatedI have upgrade plesk to 12 version and after upgrade all the domains that have more than 2048 MB on the server are shown as 2048 MB.
If i go on the domain statistic the tab the total disk usage is 2048.1 MB but on the graph the services disk usage are shown correctly.
I have 2 print screen.
It appears that my clients disk space usage calculation is including admin full server FTP backups that I am doing.
This shouldn't be the case, these full server backups that I'm doing should not count towards my clients plans disk space allowance.
I migrated from one server running Plesk 10.4.4 Update #59 to a new server running Plesk 11 which I then updated to 12.0.18 Update #32. Since moving to Plesk 12 the "Notify when disk space/traffic usage reaches" emails have been being sent to our customers set up on the server whereas previously they were sent to the server admin email address.
Is this a change with this version?
My server has a small SAS disk(about 73G), if I use 90% diskspace of it, is it good idea, will it harm the physical HDD?
View 6 Replies View RelatedI am looking for better disk performance. Due to the tight budget, I have to choose one of following options as my disk choice:
2 SATAII disk w/RAID0, 7200rpm, 32M cache for each disk
1 SAS disk, 15000rpm, 16M cache.
which one will be better and how better if other things(hardware & OS) are same?
can a Xen disk image be converted to a diskpartition?
Someone is asking whether I can host his disk image at his current host, which he is leaving for poor I/O (wonder why that would be ). I can host a diskimage, but I don't like diskimages (slow, and 100GB isn't very 'comfortable' either). Is there any way out there to convert a disk image into a normal partition?
I use apache with CentOS VPS hosting for my blog. I only host one blog in this VPS account. I have 1.5GB RAM and I have 7, 500 page preview per day. My page loading time is 2-3 seconds (according to the pingdom tool).
I want to know what is the best performance (faster web page loading) W3 Total cache option for VPS hosting blog. Currently I use Disk to enhance for page cache and database cache for disk.
i have CentOs5 / Plesk Panel / VPS Server ...
and i install APF now with this /etc/apf/conf.apf FILE ......
PHP Code:
IG_TCP_CPORTS="20,21,22,25,53,80,110,143,443,465,993,995,8443"IG_UDP_CPORTS="37,53,873"EGF="1"EG_TCP_CPORTS="20,21,22,25,53,37,43,80,113,443,465,873,5224"EG_UDP_CPORTS="53,873"
==================================
and i changed the interface to this venet0
PHP Code:
# Untrusted Network interface(s); all traffic on defined interface will be# subject to all firewall rules. This should be your internet exposed# interfaces. Only one interface is accepted for each value.IFACE_IN="venet0"IFACE_OUT="venet0"
==================================
when i finish it and restart my apf its shows me like this ???
PHP Code:
[root@box ~]# apf -sapf(3107): {glob} activating firewallapf(3149): {glob} determined (IFACE_IN) venet0 has address 127.0.0.1apf(3149): {glob} determined (IFACE_OUT) venet0 has address 127.0.0.1apf(3149): {glob} loading preroute.rulesiptables: Unknown error 4294967295iptables: Unknown error 4294967295iptables: Unknown error 4294967295iptables: Unknown error 4294967295iptables: Unknown error 4294967295iptables: Unknown error 4294967295iptables: Unknown error 4294967295apf(3149): {resnet} downloading http://r-fx.ca/downloads/reserved.networksapf(3149): {resnet} download of http://r-fx.ca/downloads/reserved.networks failedapf(3149): {glob} loading reserved.networksapf(3149): {glob} SET_REFRESH is set to 10 minutesapf(3149): {glob} loading bt.rulesapf(3149): {dshield} downloading http://feeds.dshield.org/top10-2.txtapf(3149): {dshield} download of http://feeds.dshield.org/top10-2.txt failedapf(3149): {sdrop} downloading http://www.spamhaus.org/drop/drop.lassoapf(3149): {sdrop} parsing drop.lasso into /etc/apf/sdrop_hosts.rulesapf(3149): {sdrop} loading sdrop_hosts.rulesapf(3149): {glob} loading common drop portsapf(3149): {blk_ports} deny all to/from tcp port 135:139apf(3149): {blk_ports} deny all to/from udp port 135:139apf(3149): {blk_ports} deny all to/from tcp port 111apf(3149): {blk_ports} deny all to/from udp port 111apf(3149): {blk_ports} deny all to/from tcp port 513apf(3149): {blk_ports} deny all to/from udp port 513apf(3149): {blk_ports} deny all to/from tcp port 520apf(3149): {blk_ports} deny all to/from udp port 520apf(3149): {blk_ports} deny all to/from tcp port 445apf(3149): {blk_ports} deny all to/from udp port 445apf(3149): {blk_ports} deny all to/from tcp port 1433apf(3149): {blk_ports} deny all to/from udp port 1433apf(3149): {blk_ports} deny all to/from tcp port 1434apf(3149): {blk_ports} deny all to/from udp port 1434apf(3149): {blk_ports} deny all to/from tcp port 1234apf(3149): {blk_ports} deny all to/from udp port 1234apf(3149): {blk_ports} deny all to/from tcp port 1524apf(3149): {blk_ports} deny all to/from udp port 1524apf(3149): {blk_ports} deny all to/from tcp port 3127apf(3149): {blk_ports} deny all to/from udp port 3127apf(3149): {pkt_sanity} set active PKT_SANITYapf(3149): {pkt_sanity} deny inbound tcp-flag pairs ALL NONEapf(3149): {pkt_sanity} deny inbound tcp-flag pairs SYN,FIN SYN,FINapf(3149): {pkt_sanity} deny inbound tcp-flag pairs SYN,RST SYN,RSTapf(3149): {pkt_sanity} deny inbound tcp-flag pairs FIN,RST FIN,RSTapf(3149): {pkt_sanity} deny inbound tcp-flag pairs ACK,FIN FINapf(3149): {pkt_sanity} deny inbound tcp-flag pairs ACK,URG URGapf(3149): {pkt_sanity} deny inbound tcp-flag pairs ACK,PSH PSHapf(3149): {pkt_sanity} deny inbound tcp-flag pairs ALL FIN,URG,PSHapf(3149): {pkt_sanity} deny inbound tcp-flag pairs ALL SYN,RST,ACK,FIN,URGapf(3149): {pkt_sanity} deny inbound tcp-flag pairs ALL ALLapf(3149): {pkt_sanity} deny inbound tcp-flag pairs ALL FINapf(3149): {pkt_sanity} deny outbound tcp-flag pairs ALL NONEapf(3149): {pkt_sanity} deny outbound tcp-flag pairs SYN,FIN SYN,FINapf(3149): {pkt_sanity} deny outbound tcp-flag pairs SYN,RST SYN,RSTapf(3149): {pkt_sanity} deny outbound tcp-flag pairs FIN,RST FIN,RSTapf(3149): {pkt_sanity} deny outbound tcp-flag pairs ACK,FIN FINapf(3149): {pkt_sanity} deny outbound tcp-flag pairs ACK,PSH PSHapf(3149): {pkt_sanity} deny outbound tcp-flag pairs ACK,URG URGapf(3149): {pkt_sanity} deny all fragmented udpapf(3149): {pkt_sanity} deny inbound tcp port 0apf(3149): {pkt_sanity} deny outbound tcp port 0apf(3149): {blk_p2p} set active BLK_P2Papf(3149): {blk_p2p} deny all to/from tcp port 1214apf(3149): {blk_p2p} deny all to/from udp port 1214apf(3149): {blk_p2p} deny all to/from tcp port 2323apf(3149): {blk_p2p} deny all to/from udp port 2323apf(3149): {blk_p2p} deny all to/from tcp port 4660:4678apf(3149): {blk_p2p} deny all to/from udp port 4660:4678apf(3149): {blk_p2p} deny all to/from tcp port 6257apf(3149): {blk_p2p} deny all to/from udp port 6257apf(3149): {blk_p2p} deny all to/from tcp port 6699apf(3149): {blk_p2p} deny all to/from udp port 6699apf(3149): {blk_p2p} deny all to/from tcp port 6346apf(3149): {blk_p2p} deny all to/from udp port 6346apf(3149): {blk_p2p} deny all to/from tcp port 6347apf(3149): {blk_p2p} deny all to/from udp port 6347apf(3149): {blk_p2p} deny all to/from tcp port 6881:6889apf(3149): {blk_p2p} deny all to/from udp port 6881:6889apf(3149): {blk_p2p} deny all to/from tcp port 6346apf(3149): {blk_p2p} deny all to/from udp port 6346apf(3149): {blk_p2p} deny all to/from tcp port 7778apf(3149): {blk_p2p} deny all to/from udp port 7778apf(3149): {glob} loading log.rulesapf(3149): {glob} virtual net subsystem disabled.apf(3149): {glob} loading main.rulesapf(3149): {glob} opening inbound tcp port 20 on 0/0apf(3149): {glob} opening inbound tcp port 21 on 0/0apf(3149): {glob} opening inbound tcp port 22 on 0/0apf(3149): {glob} opening inbound tcp port 25 on 0/0apf(3149): {glob} opening inbound tcp port 53 on 0/0apf(3149): {glob} opening inbound tcp port 80 on 0/0apf(3149): {glob} opening inbound tcp port 110 on 0/0apf(3149): {glob} opening inbound tcp port 143 on 0/0apf(3149): {glob} opening inbound tcp port 443 on 0/0apf(3149): {glob} opening inbound tcp port 465 on 0/0apf(3149): {glob} opening inbound tcp port 993 on 0/0apf(3149): {glob} opening inbound tcp port 995 on 0/0apf(3149): {glob} opening inbound tcp port 8443 on 0/0apf(3149): {glob} opening inbound udp port 37 on 0/0apf(3149): {glob} opening inbound udp port 53 on 0/0apf(3149): {glob} opening inbound udp port 873 on 0/0apf(3149): {glob} opening outbound tcp port 20 on 0/0apf(3149): {glob} opening outbound tcp port 21 on 0/0apf(3149): {glob} opening outbound tcp port 22 on 0/0apf(3149): {glob} opening outbound tcp port 25 on 0/0apf(3149): {glob} opening outbound tcp port 53 on 0/0apf(3149): {glob} opening outbound tcp port 37 on 0/0apf(3149): {glob} opening outbound tcp port 43 on 0/0apf(3149): {glob} opening outbound tcp port 80 on 0/0apf(3149): {glob} opening outbound tcp port 113 on 0/0apf(3149): {glob} opening outbound tcp port 443 on 0/0apf(3149): {glob} opening outbound tcp port 465 on 0/0apf(3149): {glob} opening outbound tcp port 873 on 0/0apf(3149): {glob} opening outbound tcp port 5224 on 0/0apf(3149): {glob} opening outbound udp port 53 on 0/0apf(3149): {glob} opening outbound udp port 873 on 0/0apf(3149): {glob} opening inbound icmp type 3 on 0/0apf(3149): {glob} opening inbound icmp type 5 on 0/0apf(3149): {glob} opening inbound icmp type 11 on 0/0apf(3149): {glob} opening inbound icmp type 0 on 0/0apf(3149): {glob} opening inbound icmp type 30 on 0/0apf(3149): {glob} opening inbound icmp type 8 on 0/0apf(3149): {glob} opening outbound icmp all on 0/0iptables: Unknown error 4294967295iptables: Unknown error 4294967295iptables: Unknown error 4294967295iptables: Unknown error 4294967295iptables: Unknown error 4294967295apf(3149): {glob} resolv dns discovery for 207.218.192.38iptables: Unknown error 4294967295iptables: Unknown error 4294967295iptables: Unknown error 4294967295iptables: Unknown error 4294967295iptables: Unknown error 4294967295iptables: Unknown error 4294967295iptables: Unknown error 4294967295iptables: Unknown error 4294967295iptables: Unknown error 4294967295iptables: Unknown error 4294967295iptables: Unknown error 4294967295apf(3149): {glob} loading postroute.rules
I'm just looking for some background information or a place where I can learn more about this.
Here's the problem:
The web site runs on a dedicated Apache server. There's 2 SSL certificates installed, one for e-commerce for https://www.mysite.com and one to help with the administrative interface for https://admin.mysite.com. I run a custom php application that forces the web page from http://www.mysite.com to https://www.mysite.com when going to an e-commerce page.
Generally everything runs Ok but a few times this year there has been a problem where the php application points to https://www.mysite.com/ecom.php but instead it gets https://admin.mysite.com/ecom.php and gets a page not found.
In discussing this with my web hosting company they claim they haven't changed anything but they do manage to fix the problem and get the web site working correctly again.
I generally figure that the web hosting company has done some type of maintenance on the web server and messed-up the dns entries or something for the SSL part of the web site but this is really outside my area of experience. I'm trying to understand what went wrong and where the entries are that determine when going to SSL which SSL certificate/URL is used.