i want to buy a vps to run my personal usage, and i can put some data on it and connect it anywhere, i hope to install winxp or vista on vps, and use windows's Remote Desktop to connect it, is it possible?
View 4 RepliesI have a server and I need to use several domains with it. it has apache, php, mysql all installed on it, also, I set up ns1.mydomain.com and ns2.mydomain.com to it's IP address. I downloaded SimpleDNS and I'm having trouble setting it up though. Can somebody give me a clue on what to do now?
View 0 Replies View Relatedmy school-issued laptop needs to be "unjoined" from their Active Directory domain.
They provide a tool to do this, but it also does some other nasty stuff. I'd like to remove myself from the domain by hand. I am an administrator on the local machine.
OKay here is the set up:
I have a CENTOS 64bit running, with 1 guest OS (WinXP) in a VMWare Server. I have tried the following: I have 6 public IP's attached to my 1 Ethernet card in the CENTOS host.
Try 1:
The Guest OS is set to use "Bridged" Networking. This allows full use of the internet, in both directions. Not exactly optimal, but it does work. I can reach the Guest via RD, which is a requirement for this client. The guest OS is mainly assigned one of the 6 public IP's (x.x.x.118). The problem with this setup is the Guest OS can not reach the host. For example the host has a mail server on it, and when the Guest tries to reach the host, it times out.
Try 2:
The Guest OS is set up to use "NAT" and gets 192.168.100.128 as its IP via DHCP inside of VMWare. The nat config file for VMWare is set to open port 3389 (RD port). Guest OS can reach the host with out any problem, and can reach the internet with out any problem, however I can not RD in to the Guest OS.
I prefer setup number 2 for all the obvious reasons, but I just can not get my IPTables rules to work. This is what I thought should work, but does not:
iptables -t nat -I PREROUTING -d x.x.x.118 -j DNAT --to-destination=192.168.100.128
iptables -t nat -I POSTROUTING -s 192.168.100.128 -j SNAT --to-source=x.x.x.118
I realize that would have done all traffic, and defeated the benefits of NAT,but since forwarding only 3389 was not working I tried forwarding everything.
Any suggestions?
I just setup my new Windows 2008 Server. My backed up files are on a Win XP machine. Now, I've tried everything I can think of to connect the two so I can transfer them over. But I can't. Neither machine can see the other, but they are on the same subnet and workgroup. No changes I make to sharing on either machine seems to work.
View 5 Replies View RelatedKevin Yank's book does not deal with Vista, and I'm completely stuck - whereas it was straightforward to install PHP on XP, nothing fits with Vista's IIS. Any idea where I could find the procedure ? I've tried quite a few sites, but nada.
View 4 Replies View Relatedhow to setup a SVN repository on Vista, i don't want to use is as actual server but want version control on my work pc
View 0 Replies View RelatedI can not login to any of my cpanels with vista I've tried FF and IE7 and I can't get in.
The crazy thing is that I can get into my WHM but I can't even login to the cpanels from there.
I don't have the firewall on and everything that I know of is off.....
I'm looking to run this small telnet script to reboot my router using vistas built-in telnet client:
192.168.1.1 23
WAIT "login"
SEND "my_login_idm" (enter your login ID here)
WAIT "Password"
SEND "my_login_passm" (enter your password here)
WAIT "#"
SEND "rebootm"
WAIT "#"
...without much luck.
I heard that superfetch speeds up your computer by using the memory and flash memory as cache or swap insted of the hard drive.
I tried to enable superfetch on my vista but could not find any such service or entry or any clue on the help file either..
what it is and why its not present on my pc.
I'm moving from my old XP PC to a new PC with Vista (a mistake, but that's a different story).
I'm trying to set up some sites in IIS so that I can develop locally without having to publish to a remote web server.
I've installed IIS7 from the control panel, and am now looking to set up my first site. I've put the site name in, and the path to the site on the computer, but I'm getting an error in the 'bindings' section. I've left all of this empty because I don't know what it means (it didn't ask for any of this in IIS on XP) but when I try to add the site it gives me the following error:
"The binding '*:80:' is assigned to another site. If you assign the same binding to this site, you will only be able to start one of the sites. Are you sure that you want to add this duplicate binding?"
Does anyone know what to do here? I'll need to add about 100 domains to IIS so I want them all to be accessible locally. How do I do this?
I've been working all day with members at ubuntu forums, I need serious help please
ubuntuforums.org/showthread.php?p=2067895&posted=1#post206789
I restarted again in live boot mode of course and now when I go to computer I see the 104.8GB volume drive. (wasn't there before), this is the Windows partition
When I try to open it I get an error
unable to mount the selected volume
error: device /dev/sda2 is not removable
error: could not execute pmount
So I ran sudo mount /dev/sda2 /media/windows -t ntfs -r -o uid=999,gid=999,umask=444
and now I get "you do not have the permissions necessary to view the contents of 'windows'
i'm using Vista RTM, and so then
my PHP module can load mysql 5.0.27.
Apache version: 2.0.55 ( ok )
PHP version: 5.2.0 ( unzip package - ok)
MySQL version: 5.0.27 ( connection is ok only with cmd line )
so, what's the problem.
i tried with this solution:
[url]
but it's take no effect.
what's the step i have been lost?
I have Vista Premium. I just added IIS7 to it. When I run IIS Manager I get an error window saying:
"The file that stores your list of connections and layout preferences is corrupt and cannot be recovered. The US Manager connection list and layout will return to the default state."
Then when I click on OK I get another "Failed to Connect" error window saying:
"There was an error connecting. Do you want to specify a different set of credentials?
Details could not load file or assembly 'System.web, version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3... or one of its dependencies. The system cannot find the file specified. "
I have an somewhat unusual requirement. I need a hosted Vista or XP desktop somewhere.
This is not to host a server application. The reason I need it is that I need to give my staff access to an application that only runs on an XP or vista desktop environment, and I dont want the software in question installed on their pc, instead they will log on via remote desktop and use it that way. The application does *not* run on Win Server 2003.
I have looked high and low, but all the Windows VPS services on the market seem to be hosting Win Server 2003 exclusively, which is no use to me. Does anyone out there know if it is possible to get hosted XP or Vista anywhere?
I am aware that there are a couple of providers who will host a vmware vm for you but even they seem to be oriented towards Win Server, which is no use to me.
I have Vista Premium. I just added IIS7 to it. When I run IIS Manager I get an error window saying:
"The file that stores your list of connections and layout preferences is corrupt and cannot be recovered. The US Manager connection list and layout will return to the default state."
Then when I click on OK I get another "Failed to Connect" error window saying:
"There was an error connecting. Do you want to specify a different set of credentials?
Details could not load file or assembly 'System.web, version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3... or one of its dependencies. The system cannot find the file specified. "
What's going on?
Well, my company got a Windows 2003 Small Business Server and most of our workstations were running Windows Vista. Now I ran into some issues I thought I'd document for the benefit of those attempting connections of Vista Business and up workstations to a Windows 2003 Small Business Server:
Windows 2003 Small Business Server Vista and Outlook 2007 Compatibility Upgrade
Before you throwing your Vista clients at your Windows 2003 Small Business Server, you're going to need to make sure you have the Windows Vista and Outlook 2007 compatibility update as outlined by KB926505, the knowledge base entry on Vista and Windows 2003 SBS. This will require a restart of the server to fully apply the effects of the patch.
Updating workstations with existing users
Now, you add your users through the Server Management tool, and it tells you to run [url]on the client workstation to setup the process. Before you do this, you need to separate out your systems with existing users (and thus profiles) and your systems with no established users. For the ones that have existing users, you'll need to install a Win32_UserProfile WMI patch. If you don't apply this patch, then you can't migrate your local PC user settings to the Windows 2003 SBS associated user when you run the setup (Unless you install the patch, then re-run the wizard).
Running the connection wizard
Okay, so let's say your server is named SBS2003, now you point your client workstation to [url]and you'll be asked for the username and password of an existing user on the Windows 2003 SBS. Enter it in and 2 things can happen:
Runs without a hitch
You get an error about copying Client Setup files
Now here's the painful one. There's a number of ways to approach this issue, so be sure to go through them all:
Point your DNS servers to the Windows 2003 SBS and ONLY the Windows 2003 SBS. This solved my particular issue.
You may have an issue with required encryption in IIS. See this post for a possible solution.
You may have an issue with TCP offload. Check this post for more information. Basically you need to disable it.
IIS is bound to a specific IP. Try changing it to "All Unassigned" instead.
Now then, the wizard should run, and your workstation should now be latched onto the domain Not quite done yet though.
Network Discovery
I found my workstations couldn't see network machines after I attached them to the network. Trying to turn on Network Discovery in the Network Sharing Center seemed to fail. To rectify this, I took 2 steps:
Enabled Link Layer Topology Discovery (LLTD) for the domain to get my network map. You'll also need to make sure LLTD is enabled on your NIC properties as well (in the form of a checked box).
I had to turn on Network Discovery and File and Printer Sharing in the Windows Firewall settings. To do this I did: Control Panel
Windows Firewall
Bring up the exceptions tab
Make sure Network Discovery and File and Printer Sharing were enabled
Then viola, network thar she blows. Also, I found that when I shared directories on the Windows 2003 SBS and the client had permissions to access the share, it wouldn't showup until I went to the Publish tab in the share's properties on the server and made it published on active directory. After doing that and refreshing my Windows 2003 SBS showed up in the Network.
Yesterday I could reach all of my cPanels on a Vista laptop; today they all time out. I can reach them with other computers. It doesn't matter if I go to mysite.com/cpanel or mysite.com:2082. I even added a port 2082 under Windows Firewall; no change. I'm not using any 3rd party firewalls. I did install a bittorrent client last night, then uninstalled it when it didn't work.
View 3 Replies View RelatedI cannot get IIS to work on Vista Home Premium.
I have installed it as per instructions, turned off firewall etc
It appears to be installed but when I try [url]I just get the "internet explorer cannot display the webpage" page
I have a customer that relies heavily on her email (sends/receives about 200 emails each day). Last Friday we traded her Windows XP computer for a new Windows Vista system.
Now since that time one of her main contacts is unable to receive any emails. She is able to receive messages from that contact but the replies are not received by the customer. I talked with the technical support group on the receiving end and they tracked it back and said that the emails are sitting in their spam filter.
What change(s) were made that changed this trusted email account to a spam account just by upgrading to Vista? I ran the DNS Tools Spam tool and the domain and IP address is not listed in any database. The only thing that showed was something about the PTR not found in the domain record. Is this something that is required?
When I try to activate IIS7 in Windows Vista Ultimate 64-bit everything seems to go well but after a while when the progress bar has gone full and that window has disappeared an error message appears saying "An error has occured. Not all features were successfully changed". If I don't restart immediately but instead try to open the IIS7 default page it's up. But after rebooting it's gone. The iis7.log says:
Code:
[09/10/2009 16:04:51] < !!FAIL!! > SERVICE_CONTROLLER::StartNamedService APPHOSTSVC result=0x80070424
[09/10/2009 16:04:51] < !!FAIL!! > Install of component ProcessModel result=0x80070424
[09/10/2009 16:04:51] < !!FAIL!! > COMPONENT::ExecuteCommand result=0x80070424
i got a new computer with vista and i was attempting to check out one of my own websites and i get the following error:
There is a problem with this website's security certificate.
The security certificate presented by this website was not issued by a trusted certificate authority.
Security certificate problems may indicate an attempt to fool you or intercept any data you send to the server.
We recommend that you close this webpage and do not continue to this website.
Click here to close this webpage.
Continue to this website (not recommended).
i guess at that initial point, most people will bail. but if they are brave enough to forge ahead, they then get this:
This error occurs when the certificate has been issued by a certification authority that is not recognized by Internet Explorer. It is unlikely that this error will occur on a legitimate business or banking site. Phishing sites often attempt to use fake certificates that will trigger this error.
and of course, there is no lock icon at the bottom of the page. there is not even a way for me to install the certificate. this seems libelous to me.
My roommate ran into this problem a few weeks ago. He could not connect to a webserver. Turns out it is the way that some of the ports are being handled when passive FTP is used.
I was wondering if a lot of web hosting companies are seeing some complaints of (passive) FTP not working properly? And who are you blaming?
He had to install some firmware updates to the Linksys router as well but then that started to crash the Internet connection (something we cannot have). So the router update was uninstalled.
He had to do quite a bit and finally started to use the control panel to upload. He has not tried FileZilla yet but I tried it on my system to connect to his server and it failed.
I'd like to ask for opinion what is the best way to backup a client PC in Windows XP/Vista platform.
For example, each PC has a folder inside c:Server
Every 17:00 hours, the PC will FTP all data inside c:Server to backup server.
When it is done, the manager is able to access to his files & do his work remotely online via the server at night in his home. Another reason to have this backup is because they want to secure all the files from any viruses or any accidents in the office during non office hours as the files is important to them. The next morning, he is able to continue his work as normal when files are being merged.
Any kind of such solution available?
Does anybody know how I can force RSYNC to backup open files on Windows 2003 Standard and Vista Ultimate?
View 4 Replies View RelatedIs it possible to install Plesk 12 to Debian Jessie with the autoinstall script?
View 7 Replies View Relatedproblem with install suhosin and ...
how i can install Mod_security
What difference between yum install php or manually install php from scrach (build, make and install)?
I know manually install could configure lots of parameters and paths, like --iconv, --mbsting, etc. I don't know anything behind yum install php. If I want to install php everything in the following:
./configure --prefix=/usr/local/webserver/php --with-config-file-path=/usr/local/webserver/php/etc --with-mysql=/usr/local/webserver/mysql --with-mysqli=/usr/local/webserver/mysql/bin/mysql_config --with-iconv-dir=/usr/local --with-freetype-dir --with-jpeg-dir --with-png-dir --with-zlib --with-libxml-dir=/usr --enable-xml --disable-debug --disable-rpath --enable-discard-path --enable-safe-mode --enable-bcmath --enable-shmop --enable-sysvsem --enable-inline-optimization --with-curl --with-curlwrappers --enable-mbregex --enable-fastcgi --enable-fpm --enable-force-cgi-redirect --enable-mbstring --with-mcrypt --with-gd --enable-gd-native-ttf --with-openssl --with-sendmail=/usr/sbin/sendmail
to installing linux software and have been beating my head for a couple of days. I just learned that I can use something on my CENTOS 5 - which is the same as RHEL 5 - to install the rpm and all dependencies.
Numeric-24.2-1.i586.rpm is the rpm I want to install, if that matters.
How can I do install it AND any dependencies?
I am trying to install the kernel source.
I have downloaded kernel-2.6.20-1.2948.fc6.src.rpm
I am using fedora 6 64bit.
here are my current kernels:
kernel-headers-2.6.20-1.2948.fc6
kernel-devel-2.6.20-1.2944.fc6
yum-kernel-module-1.0.3-1.fc6
kernel-2.6.20-1.2944.fc6
kernel-devel-2.6.20-1.2948.fc6
kernel-2.6.20-1.2948.fc6
here is what I seen when I installed kernel-2.6.20-1.2948.fc6.src.rpm
rpm -ivh kernel-2.6.20-1.2948.fc6.src.rpm
1:kernel warning: user brewbuilder does not exist - using root
warning: group brewbuilder does not exist - using root
warning: user brewbuilder does not exist - using root
########################################### [100%]
warning: user brewbuilder does not exist - using root
warning: group brewbuilder does not exist - using root
then when I ran:
rpmbuild -bp --target=$(uname -m) /usr/src/redhat/SPECS/kernel-2.6.spec
I seen this error:
+ Arch=x86_64
+ make ARCH=x86_64 nonint_oldconfig
In file included from /usr/include/sys/socket.h:35,
from /usr/include/netinet/in.h:24,
from /usr/include/arpa/inet.h:23,
from scripts/basic/fixdep.c:117:
/usr/include/bits/socket.h:310:24: error: asm/socket.h: No such file or directory
make[1]: *** [scripts/basic/fixdep] Error 1
make: *** [scripts_basic] Error 2
error: Bad exit status from /var/tmp/rpm-tmp.93770 (%prep)
I need to have this installed to get a app installed etc...
suggestions or ideas?
thanks
So i have a dedicated server and here are the specs:
AMD64 X2 7750+
8192 MB DDR2 RAM
500 GB 7.200 RPM
2000 GB Traffic p/m
CentOS 5.3
I want to install several VPS's on this server so i have one for shared users, one for reseller users and then the rest can be purchased. Unfortunately i have no idea how to install VPS's. Which is the best visualization software for VPS's? And how do i install and how to get whmcs to create them. Or are they already created?
I am also wondering about control panels and do vps's have to have their own separate control panel or do they all run of the main control panel.
Also what is the rule of thumb on how many vps's per server.