Does any one try this mainboard?
I want to install CentOS 4.6 (x86_64), but most of ICH9R or ICH9 desktop board is not support CentOS 4.6.
If you are try it before, can you share your experience with me?
Does anyone know a data center in any of those two areas? In addition to general information like address and so on, I also want to know which carrier is in the facility.
View 11 Replies View RelatedI've been having a look at a lot of boards and Tyan seem to be beating Supermicro in terms of range at scan.co.uk
I've seen some unique features with Supermicro such as Remote KVM and such built into the motherboard, but it only seems to be with the very pricey series unless I'm looking in the wrong direction
Anybody have any thoughts to share about which is the better manufacturer?
Server Tyan Transport GT20 B5151
CPU P4 3.0GHZ HyperThreaded
memory 2GB Kingston RAM DDR400
3 hardisks 250 gb, 2 for raid, 1 spare
it seems very hard to install centos on this box, i cannot figure out how to do.
i used a network install, and first of all the grub loader gave an error.
i used all standard procedures for install.
i think its the raid controller messing up with it.
does somebody know or already has used such system with hardware raid controller and one spare hdd to install centos?
If you know where to buy those modules, please let me know.
View 3 Replies View RelatedI have here 3 servers of Tyan with M3291 IPMI boards installed. I hooked it up as per instructions of Tyan, but am unable to get it to work.
I have tried contacting Tyan about this, but after a few messages they stopped responding to my questions. I think they are convinced it is working with me....
The setup is;
- Ubuntu 6.1 x86_64
- System BIOS is the original version
- IPMI card is flashed with the correct firmware
- The network port which is shared with the IPMI card has a different IP address then the IPMI card.
Settings IPMI card:
box:~# ./uh8l -d
BMC Utility on Linux For M3291 version 0.9.1
Copyright 2003-2006 TYAN Computer Corp.
IPMI Ver: 2.0 Firmware Rev: 0.11 Vendor ID: 6653 Pdt ID: 5161
DHCP Disable
BMC IP Address: 10.0.1.102
MAC Address: 00:E0:81:42:4C:51
Net Mask: 255.255.255.0
Gate Way: 10.0.1.253
Broadcast ARP: Enable
This server has on the IPMI shared port the address 10.0.1.2 ...
When I try to ping the IPMI board from the server itself or from a different server I get an incomplete address in the ARP table;
? (10.0.1.102) at <incomplete> on eth2
(Also after pinging it for 1 minute...)
If I use the IPMI utilities I am unable to contact the board and do anything with the server....
I tried several settings of the IPMI board, including DHCP / ARP on and off...
Does anyone have this combination working, and how did you do this?
I purchased a Tyan S3970 (Tomcat h1000e) motherboard with a Supermicro SC820 Case, 'cuz I got a good deal on the combo. After I purchased it I realized that the back-cover does not match up, and the connector wires are short. (ie. The NIC/power LED wires do not reach the connector). Does anyone have a solution to this problem.
View 0 Replies View RelatedI got a good deal on the Supermicro SC822T-R550LPB case, and then bought a Tyan Motherboard(S3970).
Unfortunately, the IO shield that comes w/the board does not fit the case, and the one from the case does not fit the mboard. A set of FAN cables do not reach the mboard either. Does anyone know of any place that sells these parts?