I have a SuperMicro server with AOC-SIM1U.
I was able to login from IPMI View just fine, and everything works as expected except
"Text Console ". I was able to hit the start button and get the black screen on IPMI View, but that was just about it.
Only a cursor blinking without texts.
Is there something else that I should do in order to get text console working? I've tried all baud rates.
When you can't access your server via SSH or Remote Desktop, what do you use to fix the problem without filing a ticket?
IPMI?
Serial console?
KVM over IP?
Dial up connection?
Backup network connection?
Get up and walk to the server? :-)
If you had a choice between them, what did you pick and why?
Does your dedicated server provider give it to you for free, or do you have to pay extra for it?
I am having alot of difficulty trying to setup supermicro IPMI.
I am using motherboard PDSMI+.
Ok, so this is what I did:
1. I flash the IPMI card with the cd-rom that is included. I set the correct IP and MAC address.
2. I then install OpenIPMI-tools
I was able to successfully issue the command locally:
ipmitool sensor
but, when I try to connect remotely I always get a connection failed. I tried everything I know, which is nothing and got no progress.
I set the ipaddres and gateway by using this commands:
ipmitool -I open lan set 1 ipaddr [IPADDR]
ipmitool -I open lan set 1 defgw ipaddr [GW IPADDR]
ipmitool -I open lan set 1 netmask [NETMASK]
ipmitool -I open lan set 1 access on
I have a bunch of servers with IPMI cards with KVMoIP capability and I know how to configure IPs and everything using IPMICFG.EXE while the system boots.
Now, I am facing a dilemma as to how to create the IP space.
When I create a user I specify the user has no access to change the network (IP) info.
But say the user has windows server, are they able to change the IP from there using IPMICFG.EXE?
This will determine how I create my VLANs.
If the client with USER access is able to change the IP settings using IPMICFG.exe then I have to create a /30 VLAN for each KVMoIP. I dont want to do this cause 3 IPs are wasted.
If the user will not be able to execute IPMICFG.EXE then I can just create one big VLAN and assign one IP per IPMI card with the gateway being the same for the entire big VLAN.
Any experiences with Supermicro IPMI Card - (AOC-IPMI20-E)? I need basic Power managment like APC reboot ports.
Since its very likely that we will get some Supermicro servers, I thought why not add the IPMI card.
i have setup fresh Centos 6.5 with Plesk Pannel 12.0.18. When i execute the attached command from the console, i get it work, some posts are auto created within wordpress. When i enter the attached command within Plesk (Tools / Settings - Taskmanager - root New Task, the command is not executed...
/usr/bin/wget --post-data='id=4&minposts=1&maxposts=3' -O /dev/null http://www.mydomain.com/wp/wp-content/plugins/WPRobot3/cron.php?code=UNIQUEID
I tried also without /usr/bin at the beginning, but its not working with cron automatic
What are the benefits of IPMI with KVM Over LAN? Is it more of a benefit for the datacenter? Or does it have benefits for someone that has collocated there server a far distance away?
View 14 Replies View RelatedThis may appear to be a stupid question, but I just wonder if the Supermicro IPMI cards work only with Supermicro hardware (or if it works also with other hardware, but without warrantly)?
In case does it exist some hardware independant, or something similar?
Say a server has 2 gig-e ports on board, and the OS
is using both. Can I still use IPMI feature? Or do I have
to get an additional ethernet card?
I'm in the market for a new server for colocation, and to save myself some of the headaches I've had with my current one, I'd like it to have a good remote management system, specifically one that operates independently of the operating system, or ideally one that can be accessed even if the machine is powered off. What exactly should I be looking for? I've read a lot about IPMI and Intel vPro and AMT, and I'm not quite clear on how they all fit together.
At the very least, I need something that will let me power-cycle the machine and remotely access its serial console. All the hardware environment monitoring things in IPMI sound useful, but not essential for my purposes. Anyway, it sounds like vPro is part of many (or all?) current Core 2 processors, or am I mistaken? I'm looking mainly at machines with Core 2 Duo or Quad, so can I expect they'd have that built-in, or would I need to specifically request it or look for some particular chipset or CPU?
I am going to purchase SuperMicro server with IPMI card which I can do remote control...but should I add KVM swtich for extra backup?
If so, what kind should I get for 1-3 servers? IP based? Any recommendation?
I have here 3 servers of Tyan with M3291 IPMI boards installed. I hooked it up as per instructions of Tyan, but am unable to get it to work.
I have tried contacting Tyan about this, but after a few messages they stopped responding to my questions. I think they are convinced it is working with me....
The setup is;
- Ubuntu 6.1 x86_64
- System BIOS is the original version
- IPMI card is flashed with the correct firmware
- The network port which is shared with the IPMI card has a different IP address then the IPMI card.
Settings IPMI card:
box:~# ./uh8l -d
BMC Utility on Linux For M3291 version 0.9.1
Copyright 2003-2006 TYAN Computer Corp.
IPMI Ver: 2.0 Firmware Rev: 0.11 Vendor ID: 6653 Pdt ID: 5161
DHCP Disable
BMC IP Address: 10.0.1.102
MAC Address: 00:E0:81:42:4C:51
Net Mask: 255.255.255.0
Gate Way: 10.0.1.253
Broadcast ARP: Enable
This server has on the IPMI shared port the address 10.0.1.2 ...
When I try to ping the IPMI board from the server itself or from a different server I get an incomplete address in the ARP table;
? (10.0.1.102) at <incomplete> on eth2
(Also after pinging it for 1 minute...)
If I use the IPMI utilities I am unable to contact the board and do anything with the server....
I tried several settings of the IPMI board, including DHCP / ARP on and off...
Does anyone have this combination working, and how did you do this?
We've been investigating software and appliances that would allow us a central, web based login to manage access and users to all the servers with IPMI cards. Does anyone use anything other than appliances from avocent or raritan?
View 2 Replies View RelatedI have a question maybe someone can help with. Is it possible to set the IP address on a IPMI card before a system ships? That way when the customer gets it, it already has the IP address set to whatever was agreed on and they can log right in using that IP address?
The card is a supermicro Supermicro AOC-SIMLC
I've noticed on some rackmount servers and firewall appliances there are ports labelled console, and look like serial ports. Are these related to connecting to KVM? I am looking for a cheap appliance for some rackmount servers I have (1U half depth would be ideal), to remotely recover the server if it goes down. I figured they'd connect through PS2 connectors, but then I thought that if the console port was related, then going through that might have the option for power cycling or something.
View 7 Replies View RelatedI'm trying to knock a bug out of our new Hardy Heron Xen template. Basically when the old ones boot up /bin/sh is spawned on the console. Now with Hardy init has been replace with /etc/event.d handling.
So I've replace /etc/event.d/ttyS0 and ttyS1 (not sure which one is the console but I think ttyS0)
Code:
# tty0 - shell
# This service maintains a getty on tty1 from the point the system is
# started until it is shut down again.
start on stopped rc2
start on stopped rc3
start on stopped rc4
start on stopped rc5
stop on runlevel 0
stop on runlevel 1
stop on runlevel 6
exec /bin/bash
respawn
Is there a good one around on the internet?
HyperVM has a nice one.
Terrible
[url]
I see following error in comand console.
I know its firewall log, but how can disable show firewall logs in command console?
See: [url]
I am upgrading my current colo'd server from a 1U dual core xeon with 2x500GB drives to a 2U core 2 quad with 8x750GB drives (raid5).So far I have ran into two issues. One is the rails are too large for the cabinets (problem #1 which I put in another thread). The only other problem is I am having problems with remote console on the new hardware.
It should be setup correctly since I basically rsync'd everything from the old server to the new one. The device is detected:
root@houkouonchi: 03:19 AM :~# dmesg | grep -i tty
Command line: root=/dev/sda2 gpt pci=nomsi console=tty0 console=ttyS0,9600 notsc
Kernel command line: root=/dev/sda2 gpt pci=nomsi console=tty0 console=ttyS0,9600 notsc
console [tty0] enabled
console [ttyS0] enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
But when I connect to the digi I am not getting any console output. I have tried a different serial -> Ethernet adapter and tried a different patch cable/port on the digi so I am pretty sure those are fine. The motherboard (nforce 650i chipset) didn't have an onboard serial port so I am using a port hooked up to a bracket which has a ribbon cable which connects to the motherboards COM port. I also tested another serial connector which the case has built in and both give me problems.
Maybe the motherboard is just busted?
How can change hypervm console user for a vps?
For example how can change persianwhoisvm@72.xxx.xxx.xx to microvm@72.xxx.xxx.xx
What type of cable/settings are needed to access the console port of a ProCurve 2626 J4900A? the recent one I ordered wasnt working with the regular way I access these switches.
I use a null modem (crossover) female-female serial console cable and connect it to my laptop serial port w/9600-8-1-None to access my ProCurve 2900 48G series.
But I tried using a straight/null/rollover(cisco's) and none of them worked. I also tried 9800-8-1-xoff/xon. All of them are giving me weird text when I press [ENTER] numerous times. I can access my 2900 series switches fine, no problem, just these 2626 ones I cant. My laptop can definitely detect the port cause when I disable it, I get a message on my terminal window which says "disconnected". So I am messing up somewhere.
By the way, I actually returned the switch when it came the first time because I thought they gave me a faulty one and I got another one, but it behaves the same way. But the actual switch functionality has no issues as I can assign my servers IPs and be able to access them remotely. I just cant configure the switch itself without the console port.
if anybody know the cable pin out on making a console cable using those serial adapters?
View 1 Replies View RelatedWe have a windows 2003 machine that is currently responding properly to all services that it's running (including IIS and FTP), however RDP connections just close right away and the server isn't responding when a local keyboard & monitor is plugged in.
The last thing that I want to do is pull the power out while it's on - any ideas?
I tried a remote shutdown, but the response is:
C:Users>shutdown /r /m HOSTNAME
HOSTNAME: The entered computer name is not valid or remote shutdown is not supported on the target computer. Check the name and then try again or contact your system administrator.(53)
Anybody knows a good console app. for monitoring hardware as CPU temperature etc.?
View 4 Replies View RelatedSince some days I have the strange issue that all logings from DrWeb is shown directly into the console. For example if I connect to my Server via SSH and then I sned an email to my email accoutn I see the logging of the spool.
root@************:~# 2015 Mar 25 16:44:57 * 127.0.0.1 [13727] /var/spool/drweb/spool/drweb.tmp.tWcneM - archive MAIL
2015 Mar 25 16:44:57 * 127.0.0.1 [13727] >/var/spool/drweb/spool/drweb.tmp.tWcneM/3.part - Ok
2015 Mar 25 16:44:57 * 127.0.0.1 [13727] >/var/spool/drweb/spool/drweb.tmp.tWcneM/4.part - Ok
2015 Mar 25 16:44:57 * 127.0.0.1 [13727] >/var/spool/drweb/spool/drweb.tmp.tWcneM/5.reexport - Ok
2015 Mar 25 16:44:57 * 127.0.0.1 [13727] /var/spool/drweb/spool/drweb.tmp.tWcneM - Ok
this happens in my root shell. if I disable the Email check then this will not happen anymore. another strange issue is that if I restart drweb and I have more than 1 ssh shell open I see the output of the restart on all shells, this issue is only for drweb not for any other service. How to config drweb to log only into logfile not to the console?
I search the web and the only thing I can find was
[URL]
In the FreeBSD operating system, syslog service can intercept information output by Dr.Web Daemon to the console. In this case, the information is logged character-by-character. That occurs when the logging level is set to *.info in the syslog configuration file (syslog.conf).
how can I import a database dump from the Oracle Enterprise Manager 10g console? The Oracle is running on a Red Hat Linux Server.
View 0 Replies View RelatedSay, I have a page:
say in the website of index.html there are things like
<img src="somepics.jpg">
Is there a way to set in .htaccess that we can ensure that only index.html is called?
So I do not want the client to call every image and every css file there?
How to do so?
I have a link on a site as follows: destinationsite.com/index.php?kw=test
This url is obviously going to appear in the browser window's Address bar, when the person reaches the destination page.
Is there any way to have it change the url so that the kw=test does not appear? Please bear in mind that I will not be able to change the link that the person clicks since it is with an advertising company.
my whole site is secure and inside a secure folder and I am going to be moving the majority of the site over to a non-secure folder. but I need to find all the absolute links and change the https to http. I hope I dont have to check each page one by one.
so I was wondering if there was a way to search everypage on my server for any file containing "https"?
