Since now I utilize Cisco 2924 in my racks, now I am going to install a new rack and I want to know if to install again 2924 or you recommend me 2950? what important differences (pros and cons) offers the 2950 front to 2924?
View 11 RepliesI have 2 racks in a DC that cross connected together. Now, the datacenter gives me 1 port and I would like to put 1 switch at each rack. I have successfully set up 1 switch and connect to the internet. But, I am unable to set up the other.
Below is a diagram of what I want to do: ...
My host has helped me to install a switch. However, I don't know how to configure using the command line. Could anyone help me?
I need to be able to connect to my Cisco switch using Cisco Network Assistant. If you know the command sequence,
I'm trying to learn about network. I bought Cisco 2950 for testing. I set it up and finding out the way to cap its ports at 20Mbps or 50Mbps. Do you know what command or how to do this?
Also what command to check the port speed or to uncap the port?
I'm trying to learn setting up MRTG for my Cisco 2950. Can you please give me some guide or instruction? My server runs CentOS and cPanel.
View 8 Replies View RelatedIs there much advantage to going with the 2960 series switches vs. the 2950 series? Basically I'm looking at 24 port and 48 port switches (10/100) with GBIT (copper) uplinks.
View 2 Replies View RelatedI am looking at picking up a switch to mess around with at home. I found the following within driving distance but have no idea of which one will give me more up to date, hands on experience. Any feedback is greatly appreciated.
Used Cisco WS-C5509 Chassis with power supply ( POWER SUPPLY 34-0870-01), and fan (WSC5509FAN)
Cisco WS-X5530-E2 Supervisor Engine III Modules
Cisco Systems WS-U5537-FETX CISCO 4 PORT 100BASETX UPLINK MODULE
Cisco WS-X5234-RJ45 Switch Modules X 8
$160 each.
Cisco WS-C5500 Chassis
POWER SUPPLY 34-0773-03
Cisco Ws-x5550 Supervisor Engine Iii G-series
WS-X5234-RJ45 X 11
For $200
Cisco WS-C5505 Chassis
Cisco WS-X5530-E2 Supervisor Engine III Modules
Cisco WS-U5533-FEFX-MMF Supervisor Engine III Uplink Modules
Cisco WS-X5225R Switch Modules X 2
For $140
I'm switching my colo and I currently am going to be hosting in my own colo; therefore I'm going to be switching IP addresses for all my servers.
I have a cisco switch, an APC and a few servers ... I know how to change the IP addresses within linux, but I do not know how to assign them within the switch.
Does anyone know how to do this?
Also, since I'm changing everything, does anyone know if the gateway IP address on each server has to be changed? If so, then how do you do it?
Cisco Switch IP Route setup
This is probably an easy and simple task for someone that have a good knowledge in Cisco, BGP and Blackhole/Synchole communities.
We do have a Cisco 2948G that is our border and through this equipment we apply Blackhole (a sequence of commands to filter all the traffic from the world except our country, this is done by communities that is setup in cisco).
These are the sequence of the commands to apply it for IP 189.1.XXX.40
Enter configuration commands, one per line. End with CNTL/Z. asw-hl01(config)#router bgp 184XX
asw-hl01(config-router)#network 189.1.XXX.40 mask 255.255.255.255 asw-hl01(config-router)#exit
asw-hl01(config)#access-list 50 permit 189.1.XXX.40
asw-hl01(config)#ip route 189.1.XXX.40 255.255.255.255 Null0 250 asw-hl01(config)#
I have another Cisco 2948G that is connected in a FastEthernet port of the border above, and this other cisco is holding another subnet. To make it clear,
Border - I have 189.1.XXX.1 ~ 189.1.XXX.127 (subnet 255.255.255.128)
Cisco2 - I have 189.1.XXX.128 ~ 189.1.XXX.255 (subnet 255.255.255.128)
This is being done through a ip route from Border to Cisco2 to forward subnet 128 ~ 255 to the switch,
ip route 189.1.XXX.128 255.255.255.128 172.16.1.2
Ps: 172.16.1.2 is the internal IP for switch2
Now we go to the problem. If I want to apply a Blackhole (those sequence of commands for an IP located at subnet 128 ~ 255 switch2) it block all the traffic for that given IP, and I cant get access from national backbones. To make it clear,
Blackhole for IP 1 ~ 128 - It works fine
Blackhole for IP 128 ~ 255 - It doesnt work correctly, instead of blocking only international traffic its blocking everything in the world
I recently acquired a 2950 switch brand new, this is now on production but I needed several things to be setup on the switch such as SNMP, setup an IP to access it over a browser, etc. etc.
Do you know somebody who offers a setup service for cisco switches?
new Cisco 2960 switch keeps going offline every 12 hours.
I will power cycle it, then about 12 hours later it goes off again. This is a brand new switch.
I have a Cisco 2950 and would like to make a script to activate or deactivate a switch port with snmp.
Does someone now the OID or how I can get this? I searched now very long for this in google, but I'm not able to find it.
Right im about to invest in some new equipment for the business and am looking at one of the 2 above servers. Does anyone have any experience with both or either?
The spec of the machine to start is as follows:
HP Proliant DL380 G5
Intel Quad-Core Xeon 2.5Ghz
4GB Ram
3x 146GB SAS Hotswap RAID5 (OS)
5x 146GB SAS Hotswap RAID5 (Storage)
Dell Poweredge 2950 III
Intel Quad-Core Xeon 2.5Ghz
4GB Ram
3x 146GB SAS RAID5 (OS)
5x 146GB SAS RAID5 (Storage)
Both are near identical specs and the price of the HP is slightly more, is it worth it?
a sales told me i can buy two switch and do series connection,
then if one fail,another will continue to work,
it will take high HA,
but i still can not understand how to do it and work,
could you know what it is?
Anyone know anything about cisco pix 501s? i need help setting one up if anyone can give me a hand.
View 14 Replies View RelatedI just got a Cisco PIX 501 from my IT Guy for home use and he didn't reset the firewall to default settings so there are ton of old commands in here.
Is there a command I can use to reset the firewall back to the factory default settings?
Or is there anyway I can flash it back to factory default settings?
I am interested to buy a Cisco ASA firewall. So far I have never played with this gears and I wonder if it is easy to setup.
Is there any software provided by Cisco to setup rules and ACL thru some graphic interface software ?
We are looking to replace our existing WatchGuard Firebox's with a hopefully more reliable firewall from Cisco's range although I'm a bit lost when it comes to the different ranges.
Could somebody suggest a firewall that is capable of:
1: Both NAT & Drop-in (bridge) mode
2: Pretty low bandwidth requirements, no more than 10mbit/s traffic
3: SNMP Monitoring
4: High availability pairing
I am on a tight budget for a Cisco firewall. I am browsing and seeing some affordable options in the x600 series.
Please tell me, which series is best?:
1600
2600
3600
The higher the better?..
Also what about submodels, like is 1650 better than 1600?
And how can I tell how much DRAM each one can take up to?
I see a lot of DDos related articles here at WHT. We've got hit multiple times by DDos and had to handle those attacks everytime with a different approach.
The largest one and the most well know one (we were in Times Mag, AP news, CNN, slashdot, you name it - just do a search about us on WHT) was Russian botnet cyberattack - we had to anaylyze netflow and then block everything on our edge routers, then on the firewall and then locally on the servers.
Since then we had number of other attacks, some of them we were not able to defend on the server level, while, as you can understand we can't do netwflow and manual intervention evey time somebody gets an attach.
We have very good scripts which allow to mitigate huge number of DDos attack, whet our scripts are finding attacking IPs and blocking them automatically - still some attacks could be blocked only on the router level.
I've read that Cisco Guard (I am interesed in 65xx version of it) suppose to mitigate DDos attacks in automatic mode.
after months of disruption moving servers into a new data centre, our once reliable colocation company has now had nearly 6 hours downtime in the last 16 hours. So much for network redundancy.
View 5 Replies View RelatedOther than eBay does anyone know of a supplier of Cisco gear that has good prices and knows their Cisco equipment?
View 14 Replies View RelatedI am setting up a small ccna lab and i have RIP working and i can ping my lan from both routers, but only certain hosts on the lan from the one router the setup is
LAN (192.168.1.0/255.255.255.0)
|
/
router 1 E0 192.168.1.45
Serial0 10.10.10.1
|
/
Serial0 10.10.10.2 (of router2)
|
/
E0 192.168.3.250
E1 192.168.2.250
Lo 192.168.5.4
I can ping 192.168.1.102 from router 2 and 192.168.1.45 but no not 192.168.1.201 ... or 192.168.1.1
also i can ping 192.168.5.4 from 192.168.1.102 which is a linux box and an ip route to tell it that 192.168.5.0 can be gotten from 192.168.1.45
What is the difference between the Cisco PIX and Cisco ASA Firewall Systems?
Also which firewall do you guys recommend for a rack of servers
I am currently looking at these Cisco switches:
- Cisco 2924 WS-C2924-XL-EN Enterprise Switch
- Cisco 2950 WS-C2950-24 Catalyst Switch
- Cisco 3512 WS-C3512-XL-EN Enterprise Switch
- Cisco 3524 WS-C3524-XL-EN Enterprise Switch
- Cisco 3548 WS-C3548-XL-EN Enterprise Switch
1) I was recommended to chose the XL-EN model switches because it seems they have more Memory, but the second one in the list (Catalyst) is not a XL-EN, is that going to have any affect performance wise? or it doesn't really matter?
2) I was also recommended to choose managed switches because that way I can use the SNMP features to measure bandwidth, are any of the switches above unmanaged?
3) I also want to be able to manage the switch remotely, web managed, are any of the switches above web-manageable?
4) Most importantly, when my datacenter give me a 100mbit drop, I dont know which port to plug it in in the 29** series. In the 35** I see it clearly but I am not able to see it in the 29**, any ideas?
5) On some of these switches I see a special port called "Console", what is it? where does that connect to?
6) Do any of the switches above not have a console port?
My network currently looks like this :
ISP ->> L3 Switch ->> Firewall (Transparent Mode) ->> Switch ->> Servers
I have a single /24 and my firewall is on x.2 and routes traffic for each of the servers.
Now i have a new Cisco ASA 5510 that i want to replace the aging firewall currently in place, however i dont want to put the firewall into transparent mode because i dont want to lose all the functionality.
Now with most firewalls your outside subnet cannot be the same as your inside subnet, which is fine if you are using NAT but i dont want to NAT. I need all of my servers to remain with their public ip addresses.
So what is the ideal way to setup something like this? Request my ISP give me a /30 for the ASA outside interface or something? And then ask them to route my /24 through the /30 new subnet?
whether I can grant a specific vlan priority over all other traffic..and if so does anyone know an appropriate site where I can find documentation on how to do so?
View 0 Replies View RelatedIs there such a switch?
Do cisco do a 24 port 1000Mbs switch that you can control each port speed through a web based software?
Does anyone know of a place or have for sale a Cisco PIX firewall? I have looked into ebay but was wondering what else is out there?
View 3 Replies View RelatedFrom the posts in this forum it would appear that a number of forumites are colocation service providers and web hosters that use Cisco gear.
I was reviewing the Cisco End User License Agreement that was included in the router box. Under the General Limitations section, "Customer shall have no right, and Customer specifically agrees not to:", item (iv) states, "use or permit the Software to be used to perform services for third parties, whether on a service bureau basis or time sharing basis or otherwise, without the express written authorization of Cisco".
Does this mean that a service provider is required to acquire
a separate license similar to the Microsoft Service provider license?
I have a cisco 2960G switch that I used for colocation, the colocation provider does all the routing all I need is this switch. It's just a plug and play operation, however I now need to do some more difficult stuff.
So, I plugged their bandwidth uplink into port 20.
I have really no idea on how to setup anything other than the basic of the switch.
Is it possible to setup Private Vlans in this situation? I am in need of a setup like this:
All port 1-19 in private vlans, but still able to communicate with port 20 to get internet access. Port 1-19 cannot communicate with each other except by going through port 20, through the internet.
I also want to know if it's possible to statically assign each port with a specific IP? Just say I want all traffic to a static ip to only go to port 1? Is that possible? I want to be able to limit the control of IPs through the switch not through the server.
Right now all my IPs are assign on the server level, meaning the server can take each other IPs and mess with each other connections.