I recently got a quote for server co-location at Hurricaine Electric in Fremont CA- they quoted me a good rate for my 1U server, but added that it only comes with 2.5 AMPs. My new Dell SC1450 has a 600W power supply- so it could be drawing 6.667 AMPs- any tips on how I can figure out what it's actually drawing?
View 0 RepliesWe are about to install 4 Compaq Proliant DL360 servers and a small Linsys switch into a data centre but I have no idea how many amps a small setup like this is going use? What kinda power does a server generally use and is there a way to keep the power it pulls to a minimum.
View 6 Replies View RelatedI have one Core2 Duo E6300 (TDP 65W), one 250GB HDD SATA, and one 2GB DDR2 RAM module.
How many Amps should this server use, in a 220V circuit?
I've got a 1U case and i was wondering what i could fit in there to get the most out of it. I'm looking at colocation and i'm allowed 0.4amps.
Will i be able to run a
2 x quad core xeon
4x2GB FB-DIMMs or 8x1GB FB-DIMMs
4x1TB HDD
if any of you know the charging amps of a smart ups 3000 or 2200(I cant find it on the apc site)?... I'm thinking to use it to charge a 48v golf cart... anything bad about doing this?.. I'm thinking the golf cart batteries are too large and may take a couple days to charge with the ups...
View 4 Replies View RelatedWhat do you guys think about putting 40 Amps into one rack? Our colocation provider wants to whine about it and not allow it. When we're paying them $1000+ a month - I think this is just shoddy. They say it's for heat concerns - but really this just makes me mad. We have fifteen 1U servers in there, and can't get much more on our existing 20 amps.
View 14 Replies View RelatedI would really appreciate a response from anybody who works in a datacentre or runs any R200's.
Im trying to find out how many amps a R200 is likely to use on the following specs.
Quad Core Intel® Xeon® X3360, 2.83GHz, 2x6MB Cache, 1333MHz FSB
4GB Memory, DDR2, 800MHz (4x1GB Dual Ranked DIMMs)
C1 - Onboard SATA, 1 Drive connected to Onboard SATA Controller - No RAID
160GB, SATA, 3.5-inch, 7.2K RPM Hard Drive x2
Riser with PCI-E Support (1xPCI-E x8 slot, 1x PCI-E x4 slot)
Ive been on the dell calc and they dont even have the processor that im after in their calc for me to get a bearing... even then i couldnt trust it.
Here is the actuall link to the server im talking about.
[url]
c=uk&cs=ukbsdt1&kc=305&l=en&oc=SV4R200&s=bsd&sbc=pedge_r200
I have always found this odd and do not understand enough to figure it out.
Any knowledgeable people would be cool.
My datacenter has given me 2amp circuit for my computer. It seems to run fine on it.
Looking at the back of my power supply it says the following
520Watt max
Input rating
100-240v~,50-60Hz
7A-3A
Output rating
+3.3V & +5V combined 150W max
12V combined current 39A max
(and a lot of other stuff on amps and volts for output).
Now, Watts = Volts * Amps.
So if I have 520watts and 12 volts would be 43 amps
If it means 520 watts and 3.3volts it would be 157 amps
However it seems to max at 39amps on the back for output.
I imagine input is all that matters here and at 520 watts and 100 to 240volts that would be
5.2 amps to 2.16 amps
And the thing says 7amps to 3 amps on the back for input.
So....I imagine that is the max it can pull before dying.
However, I have 4 drives, 4 ram sticks, and 2 quad core cpus all going and I would figure I am at least halfway or more of the power use.
And the power says it starts at 3amps anyway.
But I only get 2amps.
Just looking at getting a 1u box with a local provider. They provide .75amps per box.
Previously we have gone a bit crazy and gone with dell 1950s with dual quad cores and a few disks. As you can imagine these specs go well over the .75 amps.
What type of spec server would you recommend for that power? Looking at something for small scale web hosting, duall HDs and about 2gb of ram.
I am kind of new to the idea of colo and am curious how you know the amount of amps to purchase for your server? I want my machine to have enough to run efficiently without causing hardware failures.
quad-core intel xeon 3.0 ghz
8 gb ram
4 x 300 gb hdds
I have one server now which will be doing some intense PHP/MySQL serving. I want to grow into a second server that will handle the Apache server and leave MySQL on the original box.
Question is whether I can get something decent that will only pull .5 AMPS? Why? I have to choose a co-location provider and have narrowed it down to 2- the one I like very much because will give me 7U of rack space for $200 a month- but they limit you to 2 AMPS and my Dell SC1435 pulls about 1.4 at top usage.
The other option is another co-lo (closer to my home) that is just 1U space and costs $149 for the 1 Mbps burstable. So the it will cost $298 a month when I add the second server.
So can anyone suggest some decent low energy boxes for serving (for example) 250 very low storage CMS (Joomla) sites where the database backend is offloaded to another server (connected via each server's secondary LAN port)?
Here are my requirements:
A. Space: 1/2 a secured cabinet
B. Location : Bay area
C. Power: 8 amps
D. B/w: 1 Mbps
I got quotes from
A. www.bayarea.net for 1 cabinet with 20 amps $699
B. www.he.net for 1 cabinet with 15 amps $600
C. www.svcolo.com/ for 1 cabinet with 15 amps $695
I am wondering who can give me 1/2 a secured cabinet for around $300 to $400