I have a bunch of 3Ware 95** RAID arrays with BBUs. Lately the BBUs are sensing high and too high temps a lot.
The dc reports that intake temp is 74 degress and exhaust is 91 degrees. Since the RAID cards and the BBUs are at the back of the machine, its getting more hot air than cool.
Of the three raid card brands, which do you think is best and why?
I'm currently looking for a card that can do both SAS and SATA, and have four internal ports.
I have installed 3dm for checking 3ware 8086 card status, but when going to [url] it doesnt show anything. It seems cannot connect to 1080 port, even I have turned off the firewall. Have checked in its config file already to make sure the port is 1080
Is there anyone having experience with 3dm software?
When trying to load an ovzkernel it loses support for the 3ware 8006 controller. As suggested on ovzforums, it says to load the new 3dm2 tools. I tried this but when I try to install it, it says it can't find the 3dm2 binary.
View 0 Replies View RelatedI downloaded the latest 3dm2 software:
wget [url]
However, after extracting it, when I run the setup (./setupLinux_x64.bin -console) I get "Bundled JRE is not binary compatible with host OS/Arch or it is corrupt. Testing bundled JRE failed."
Can anyone give me the steps for installing 3dm2 on a centos/WHM box?
The card is a 3ware 9690SA.
Not sure if this is too specific for this forum or not, but since I've gotten great advice here in the past I'll give it a shot.
I have a colo'd production server with a 3ware 9500S-12 RAID card and 12 400GB drives attached. The drives form 3 arrays:
1) 2 drive RAID 1 (400GB)
2) 2 drive RAID 1 (400GB)
3) 6 drive RAID 5 (2TB)
plus 2 global hot spares.
For a variety of reasons I need to change this setup so that array 1) and 2) remain as is, and array 3) is removed and those 6 drives replaced with 6 new 750GB drives in JBOD mode. I've copied all the data from the RAID5 array number 3) onto 3 of the new 750 drives (the 2TB array wasn't completely full,) and I have 3 other blank 750GB drives.
What's the best / safest way to do this? Ideally I'd like to remove the 6 old 400GB drives and retain the ability to plug them all back in and get my old array back (if something goes horribly wrong doing the switch.)
Do I need to reboot into 3BM (3ware Bios Manager) to do this, or can I do it from the command line?
Is there any problem with having a drive that already contains data written to it by another system, and bringing it up on the 3ware card in JBOD mode with the data intact? (All filesystems are ext3.) I'm not going to have to reformat the drive, am I?
Is there any problem with the new drives being SATAII (Seagate Barracuda ES 750GB) but the old drives (and I think the 3ware card, and certainly my motherboard) being SATAI? I've read that this should "just work" but of course I am nervous! There are no jumpers I can see on the 750GB drives.
Will it be possible to remove the RAID 5 in such a way that I could plug the drives back in and get the array back?
Probably going to give this a shot in the near future anyway, but just wanted to check whether anyone has tried and had success putting either 3Ware 8006-2LP or 9550SX-4LP cards in Dell PowerEdge 860 systems with a couple of SATA drives instead of using the Dell PERC controllers?
View 3 Replies View Relatedwe use 3Ware's 8006-2LP sata raid controller in each of our servers for RAID1. Our servers are all Supermicro boxes with hot-swap driver carriers (ie. the 2 raided drives are in them)
One of the drives appears to be starting to crap itself as smartd is reporting issues (although tw_cli c0 shows the raid to be OK) incl. multi zone errors.
Anyway, I'd like to replace the failing drive before it becomes a real issue so i've bought a replacement (74gb raptor, just like the original) drive.
Now I've never had to replace a failing drive in any of our servers before and I used to think it would be a simple matter of simply popping out the failing drive's carrier, put the new drive in the carrier and stick it back in the server... and the raid controller would do the rest.
Yes a little naive I know but i've never had to do it before so never paid much attention .. Anyway, I've just read and re-read the 3ware docs for my controller and their instructions are VERY VAGUE ... however I do get the feeling that the process is move involved ie. I need to tell the controller (via cli or 3dm) to first 'remove' the failing drive from the raid ..and then add a new drive and then rebuild
However there is one catch .. 3dmd/3dm2 has NEVER worked on our (centos 4) servers - 3dmd crashes regularly and 3dm2 never worked. So yes I am stuck with the 3ware cli ... which I don't mind as long as someone can tell me the sequency of commands I need to issue
As this point I'm thinking what I need to do via cli is
1) tell raid controlloer to remove the failing drive on port 0
2) eject the drive carrier with the drive in question
3) insert new drive in carrier and re-insert into server
4) using tw_cli tell the controller to add the new drive to the array and to rebuild the array
Am I anywhere close to being correct? I'm sure there are some of you out there who've done this countless times before with the 3ware controllers and hotswap drive carriers ..
Just bought a new OEM 3ware 9500S-12 SATA RAID Controller from ebay for $250, is it a good deal? Does it work with SATA-II HDDs?
View 1 Replies View RelatedI'm seeing the following from dmesg:
Quote:
3w-9xxx: scsi0: AEN: INFO (0x04:0x0053): Battery capacity test is overdue:.
When I'm in the CLI console (tw_cli) and tries to test the battery, I'm seeing the following:
Quote:
//vpsXX1> /c0/bbu test
Depending on the Storsave setting, performing the battery capacity test may
disable the write cache on the controller /c0 for up to 24 hours.
Do you want to continue ? Y|N [N]:
This is a live production server with client VPSs on it. Anyone here actually did 3ware battery test before on production system? Is it ok to do this? I'm seeking someone actually performed test operation before, not from someone just assumes it will be ok.
I have a 3ware 9650SE-24M8 RAID Controller. It was working fine for a few days and today while I was changing the RAID configs and installing different OSs, it just stopped working. Now when I boot my machine up it does not even detect any hard drives or RAID controller. I looked inside the box and the LED light on the RAID controller that is usually solid green is now blinking red. I googled for solutions but all searches lead me to useless information such as blinking red lights on the server case.
View 12 Replies View RelatedAfter seeing a topic a week or go discussing RAID cards I decided to give a hardware raid card a go to see if the performance will increase in one of our boxes.
Just for the simplicity of the test, I have put them into a RAID0 formation for purely performance tests and no redundancy. I choose a 3ware RAID card and went for the 2 port 8006-2LP option rather than the 9600 (as they had the 8006-2lp and risers in stock and what I've always been told is that SATA1 and SATA2 is really a selling point rather than any performance increase but we will leave that argument there). Because we run mainly Windows systems, I have put on Windows Server 2003 x64 R2. What I am finding after installing it all is it seems pretty "slow".
The rest of the hardware is a Dual, Quad Xeon (E5410x2), 8GB ram on a Tyan motherboard. Hard drives are 160GB Western Digital 7200 RPM so I can't see quite why it feels like its not running at a peak level.
Does anyone have any applications or software to give this RAID array a test as I really don't want to order any more or roll them out on to the network to find that software raid would be a better improvement. I did try a burn in app which tests everything but it according to the 20 seconds I ran it, in average it only transferred at 2mbs.. That cant be right..
I think one possibility is the RAID drivers arn't installed correctly as its still coming "Unknown Devices" in Device Manager and it seems It wont let me manually install the drivers for the 3ware device as it doesn't like the OS even though I have the correct ones and it installed Windows with it fine (a bit longer than normal anyway)
I'm planning to run RAID 1 on my PowerEdge 860 server running CentOS 4.4 (320gb x 2 SATA II).
After doing much research, I've decided to go with 3ware 9550sx.
I have some questions regarding installing the 3ware on an existing system with an OS already installed - How do I go about doing it?
I've read that CentOS 4.4 already has the drivers for it.. Do I just configure the RAID config during the boot up?
Is this an overkill for my PE Pentium D 2.8GHZ ?
I have configured a Xen setup on a dual xeon system with a 3ware 8506 2 ports sata controller.
Array is configured in raid1 and I am using LVM.
I get really slow accesses on the virtual machines, when I create a big ext3 system, the system is nearly freezing.
i want to use q9550 with 8G RAM,
install on X7SBL-LN2,
and use for 500G SATAII to do raid 10,
about Adaptec 2405SAS and 3Ware 9650SE-4LPML,
which one will get better performance?
I am not sure exactly which model is in my server, but I know it is in the 3ware 8xxx line.
What is my best option to be alerted to a drive failure. I am running a Raid 1 setup.
I went to 3ware's sight, and wasn't sure exactly which software to download/install.
I am on Centos 5.2 32bit and have Cpanel/WHM installed.
I have a cPanel server with 4GB RAM
My server hangs time to time, once or twice a day. This is the last status when it happens.
Server Load 75.90 (2 cpus)
Memory Used 92 %
Swap Used 65.78 %
When I was still inside SSH when it happens, the processes I can see inside "top" are a lot of httpd processes.
So I "killall -9 httpd", I had to do it 30~40 times
#killall -9 httpd
#killall -9 httpd
#killall -9 httpd
x 30~40 times until no pid process found & the server load is back to normal.
Before that, I check httpd fullstatus, they look very normal, same goes to what I see inside WHM Apache status & cpu usage status.
At first I thought it was a memory problem after consulting with a server admin, so I replaced all 4GB new ram stick (such a waste)
This is my free -m
total used free shared buffers cached
Mem: 1998 1903 95 0 45 542
-/+ buffers/cache: 1315 683
Swap: 2662 36 2625
Not good ....
I got 5 wordpress and 5 statics website on this server and 100 visitors by 24H00 each day.
Question 1 : Why the memory is so low and the swap so high ?
Question 2 : Why i don't find high usage process in top command ?
Question 3 How can i resolve this problem ?
My server is very slow, High CPU, High Apache load....
I got a new server and i had setup a script on it.
No server tweaks has been done.
I run a filehosting site so it gets very slow when traffic is high.
Here is some info:
Code:
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
4135 filedip 19 0 12812 8892 2212 R 18.9 0.4 0:00.74 index.cgi
3140 apache 15 0 22624 9604 2768 S 17.3 0.5 1:54.45 httpd
3556 apache 15 0 22792 9592 2768 S 17.3 0.5 0:43.53 httpd
3739 apache 15 0 22672 9556 2744 S 17.3 0.5 1:09.67 httpd
3884 apache 15 0 22664 9560 2744 S 17.3 0.5 0:23.98 httpd
3474 apache 15 0 22672 9572 2756 R 16.1 0.5 1:34.09 httpd
3548 apache 15 0 22792 9560 2740 S 16.1 0.5 1:33.67 httpd
3991 apache 15 0 22640 9588 2756 S 15.1 0.5 0:22.44 httpd
3475 apache 15 0 22672 9580 2756 S 13.2 0.5 1:31.42 httpd
3493 apache 15 0 22664 9592 2768 S 12.9 0.5 1:15.52 httpd
3769 apache 15 0 22664 9580 2756 S 12.9 0.5 0:45.19 httpd
3638 apache 15 0 22664 9576 2756 S 12.3 0.5 0:32.82 httpd
3724 apache 16 0 22664 9580 2756 R 12.3 0.5 0:34.25 httpd
3626 apache 15 0 22672 9580 2756 S 11.7 0.5 0:52.54 httpd
4023 apache 16 0 22792 9560 2740 R 11.3 0.5 0:13.16 httpd
3882 apache 15 0 22664 9576 2756 S 10.1 0.5 0:38.56 httpd
3005 apache 15 0 22672 9588 2768 R 9.1 0.5 2:06.61 httpd
I dont know much about server managment...
how to fix this so server doesnt go slow?
I have a site that is eating up my server resources and need to know what the best solution for this is. I'm thinking of getting another server just for mysql but do not know what specs the server should be to handle the current traffic/database load and have the site run smoothly without slowing down to a snail's pace.
An alternative is to get another server just for the videos being served and leave the database and html on the current server. This is where I'm stuck and don't know what route to take with this.
My current server stats:
Dual Xeon 5130
4GB RAM
250GB
50 Mbit/sec
CentOS 3.9
Website traffic stats:
15,000 visitors/day
150,000 pageviews/day
Serving videos
I've attached screenshots of top and bandwidth usage per day. Hopefully with this information you could tell me if I need another server or if there are any things I can do to the current server to help things move faster.
I am configuring a new file server, with 11 drives and two 3ware 8506-8 raid cards.
I would like to have one hto spare shared between the two cards.
I have read on the docs that 3ware have "multiple card support" but I don't find anuthing in the documentation stating how to have two cards managing one big array.
Is it actually supported or the "multiple card support" term is just a marketing leadout to state "you can put two card in a system without conflict"?
I am running in a High load problem lately. I have one of those cheap 1and1 servers which was running fine until 2 weeks ago. Once I rebooted accidentaly, it did not come back with some unrepairable kernel errors and I had to re-image it.
I chose to reimage the server with CentOS 5, for better support. The new re-image worked fine for some days, at least so I thought and now I am having high loads. The server crashes if not monitored every moment as the load is unpredictable.
Just a restart of the Apache will bring the server back to normality, but I am not sure if it is apache or some other script to be blamed.
I have beeing monitoring through apache server-status, but I cannot organize something unusual in the high load moments.
At this moment for example:
top - 09:00:36 up 15:43, 3 users, load average: 3.57, 4.60, 5.32
Tasks: 144 total, 2 running, 142 sleeping, 0 stopped, 0 zombie
Cpu(s): 10.6%us, 6.5%sy, 0.0%ni, 18.7%id, 63.5%wa, 0.2%hi, 0.5%si, 0.0%st
12:00:29 AM CPU %user %nice %system %iowait %steal %idle
12:10:01 AM all 9.14 0.00 5.52 44.66 0.00 40.68
12:20:14 AM all 6.83 0.00 3.98 27.88 0.00 61.32
12:30:10 AM all 6.44 0.00 4.20 81.25 0.00 8.11
12:40:09 AM all 5.25 0.00 4.09 81.93 0.00 8.73
12:50:15 AM all 5.11 0.00 3.79 90.74 0.00 0.36
01:00:07 AM all 7.22 0.00 4.52 57.11 0.00 31.15
01:10:13 AM all 6.89 0.00 4.01 55.38 0.00 33.71
01:20:14 AM all 4.37 0.00 3.27 41.88 0.00 50.48
01:30:25 AM all 4.26 0.00 3.29 63.42 0.00 29.03
01:40:06 AM all 27.18 0.00 4.75 58.27 0.00 9.80
01:50:03 AM all 29.64 0.00 6.61 51.50 0.00 12.25
02:00:07 AM all 27.00 0.00 8.48 55.49 0.00 9.03
02:10:10 AM all 19.29 0.00 4.97 73.80 0.00 1.94
02:20:04 AM all 37.85 0.00 6.78 40.70 0.00 14.67
02:30:05 AM all 15.65 0.00 4.80 68.47 0.00 11.08
02:40:08 AM all 9.06 0.00 5.60 37.49 0.00 47.86
02:50:07 AM all 5.36 0.00 3.62 42.29 0.00 48.73
03:00:02 AM all 6.05 0.00 4.08 47.27 0.00 42.60
03:10:02 AM all 4.22 0.00 3.68 38.17 0.00 53.93
03:20:02 AM all 4.06 0.00 3.75 41.37 0.00 50.82
03:30:22 AM all 4.42 0.00 3.93 45.25 0.00 46.41
03:40:11 AM all 4.34 0.00 3.95 39.58 0.00 52.13
03:50:02 AM all 4.67 0.00 4.01 32.53 0.00 58.80
04:00:08 AM all 3.72 0.00 3.87 28.40 0.00 64.02
04:10:02 AM all 13.49 0.00 6.58 20.82 0.00 59.10
04:20:01 AM all 6.70 0.00 4.63 6.06 0.00 82.61
04:30:02 AM all 1.44 0.00 1.21 4.75 0.00 92.59
04:40:01 AM all 12.42 0.00 8.12 7.65 0.00 71.81
04:50:02 AM all 1.43 0.00 1.07 4.02 0.00 93.47
05:00:02 AM all 1.60 0.00 1.40 8.62 0.00 88.38
05:10:10 AM all 3.80 0.00 3.02 17.86 0.00 75.32
05:20:06 AM all 5.10 0.00 4.22 23.34 0.00 67.34
05:30:02 AM all 1.54 0.00 1.40 11.22 0.00 85.85
05:40:05 AM all 1.75 0.00 1.89 13.12 0.00 83.23
05:50:12 AM all 2.15 0.00 2.22 18.92 0.00 76.72
06:00:02 AM all 1.92 0.00 2.01 12.87 0.00 83.20
06:10:02 AM all 2.27 0.00 2.16 11.53 0.00 84.04
06:20:03 AM all 3.56 0.00 3.02 25.26 0.00 68.16
06:30:10 AM all 2.66 0.00 2.05 18.13 0.00 77.16
06:40:02 AM all 2.58 0.00 2.25 22.87 0.00 72.30
06:50:02 AM all 2.68 0.00 1.92 15.77 0.00 79.63
07:00:03 AM all 3.06 0.00 2.48 26.01 0.00 68.46
07:10:03 AM all 3.65 0.00 3.20 36.54 0.00 56.61
07:10:03 AM CPU %user %nice %system %iowait %steal %idle
07:20:03 AM all 4.40 0.00 3.28 43.86 0.00 48.46
07:30:02 AM all 4.10 0.00 3.17 31.30 0.00 61.43
07:40:06 AM all 7.67 0.00 3.95 50.79 0.00 37.59
07:50:02 AM all 4.72 0.00 3.11 44.30 0.00 47.86
08:00:03 AM all 5.57 0.00 3.72 47.15 0.00 43.56
08:10:07 AM all 10.66 0.00 3.59 71.62 0.00 14.13
08:20:17 AM all 5.67 0.00 3.42 58.81 0.00 32.10
08:30:10 AM all 11.12 0.00 3.49 76.71 0.00 8.67
08:40:03 AM all 7.00 0.00 3.36 47.94 0.00 41.71
Average: all 7.53 0.00 3.76 38.90 0.00 49.81
Some configurations:
The reimage partittioning looks like this:
/dev/sda1 950M 138M 765M 16% /
/dev/sda5 4.7G 1.9G 2.9G 40% /usr
/dev/sda7 63G 58G 5.0G 93% /var
/dev/sda6 4.7G 23M 4.7G 1% /home
none 1.0G 500K 1.0G 1% /tmp
KeepAlive On
MaxKeepAliveRequests 300
KeepAliveTimeout 15
<IfModule prefork.c>
StartServers 10
MinSpareServers 20
MaxSpareServers 50
ServerLimit 256
MaxClients 180
MaxRequestsPerChild 2000
</IfModule>
<IfModule worker.c>
StartServers 2
MaxClients 150
MinSpareThreads 25
MaxSpareThreads 75
ThreadsPerChild 25
MaxRequestsPerChild 0
</IfModule>
[mysqld]
datadir=/var/lib/mysql
socket=/var/lib/mysql/mysql.sock
skip-locking
query_cache_limit=1M
query_cache_size=32M
query_cache_type=1
max_connections=250
interactive_timeout=100
wait_timeout=20
connect_timeout=10
thread_cache_size=80
key_buffer=64M
join_buffer=1M
max_allowed_packet=16M
table_cache=512
record_buffer=1M
sort_buffer_size=1M
read_buffer_size=1M
max_connect_errors=10
thread_concurrency=2
read_rnd_buffer_size=1M
myisam_sort_buffer_size=64M
server-id=1
processor : 1
vendor_id : GenuineIntel
cpu family : 15
model : 3
model name : Intel(R) Pentium(R) 4 CPU 2.80GHz
stepping : 4
cpu MHz : 2793.324
cache size : 1024 KB
I have extremely high CPU load average, but when I run TOP command there are not any process with high CPU
CPU load averages:
211.65 (1 min) 227.29 (5 mins) 247.89 (15 mins)
Tasks: 364 total, 2 running, 360 sleeping, 2 stopped, 0 zombie
Cpu(s): 0.0%us, 0.3%sy, 0.0%ni, 0.0%id, 99.7%wa, 0.0%hi, 0.0%si, 0.0%st
Mem: 2065460k total, 2012372k used, 53088k free, 60964k buffers
Swap: 2040212k total, 3280k used, 2036932k free, 619900k cached
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
19871 root 15 0 4944 2488 1656 R 1 0.1 0:02.73 top
1 root 15 0 4208 1320 1136 S 0 0.1 0:01.55 init
2 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/0
3 root 34 19 0 0 0 S 0 0.0 0:01.77 ksoftirqd/0
4 root RT 0 0 0 0 S 0 0.0 0:00.01 migration/1
5 root 34 19 0 0 0 S 0 0.0 0:01.16 ksoftirqd/1
6 root 10 -5 0 0 0 S 0 0.0 0:01.04 events/0
7 root 10 -5 0 0 0 S 0 0.0 0:00.65 events/1
8 root 10 -5 0 0 0 S 0 0.0 0:00.00 khelper
9 root 11 -5 0 0 0 S 0 0.0 0:00.00 kthread
35 root 10 -5 0 0 0 S 0 0.0 0:00.15 kblockd/0
36 root 10 -5 0 0 0 S 0 0.0 0:00.00 kblockd/1
37 root 15 -5 0 0 0 S 0 0.0 0:00.00 kacpid
127 root 10 -5 0 0 0 S 0 0.0 0:13.16 ata/0
128 root 16 -5 0 0 0 S 0 0.0 0:00.00 ata/1
129 root 10 -5 0 0 0 D 0 0.0 0:01.15 ata_aux
130 root 10 -5 0 0 0 S 0 0.0 0:00.00 kseriod
158 root 16 0 0 0 0 S 0 0.0 0:00.00 pdflush
159 root 15 0 0 0 0 D 0 0.0 0:01.00 pdflush
160 root 10 -5 0 0 0 S 0 0.0 0:10.68 kswapd0
161 root 11 -5 0 0 0 S 0 0.0 0:00.00 aio/0
So my server is "unresponsive" for abour 18 hours, burst net didnt answer my tickets and I dont know what to do. Ive been with this setup for almost 5 months with no problems, No changes have been made to hardware or software.
Im using Centos 5.0
MY server configure our drives with RAID-1.
How can I check it my server configure with 3ware or software raid ?
Also please advise me how can I monitor raid configuration that my raid is working fine or no ?
When I run the top command on my server, my output is as follows:
=====================================
Tasks: 515 total, 50 running, 363 sleeping, 1 stopped, 101 zombie
Cpu(s): 1.1%us, 2.6%sy, 94.3%ni, 0.0%id, 0.0%wa, 0.3%hi, 1.7%si, 0.0%st
Mem: 1026792k total, 976680k used, 50112k free, 27548k buffers
Swap: 2096472k total, 466248k used, 1630224k free, 251920k cached
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
400 nobody 17 1 48592 18m 6956 R 20 1.9 0:17.65 lsphp5
6925 nobody 17 1 50008 17m 4048 R 20 1.7 0:06.15 lsphp5
13819 nobody 17 1 47900 14m 3372 R 17 1.4 0:04.23 lsphp5
24392 nobody 17 1 51084 16m 4304 S 11 1.6 0:13.07 lsphp5
3339 nobody 16 1 50620 17m 3876 D 11 1.7 0:08.43 lsphp5
358 nobody 17 1 49260 17m 5352 R 10 1.8 0:13.00 lsphp5
4059 nobody 17 1 47824 15m 4688 S 9 1.6 0:08.23 lsphp5
26979 nobody 16 1 51220 19m 5392 R 9 1.9 0:12.04 lsphp5
11864 nobody 17 1 48592 15m 4376 R 8 1.6 0:03.76 lsphp5
381 nobody 17 1 52100 19m 4576 S 7 1.9 0:09.34 lsphp5
4056 nobody 17 1 48564 15m 3932 R 7 1.5 0:06.58 lsphp5
12838 nobody 17 1 48856 16m 4088 R 7 1.6 0:06.11 lsphp5
6924 nobody 17 1 51060 15m 4188 R 6 1.6 0:04.36 lsphp5
14343 nobody 17 1 47736 13m 2712 R 6 1.3 0:00.18 lsphp5
11848 nobody 17 1 48580 16m 5268 S 5 1.7 0:06.18 lsphp5
11862 nobody 17 1 48124 14m 3848 R 5 1.5 0:04.23 lsphp5
14293 nobody 17 1 47872 13m 3020 S 5 1.4 0:00.84 lsphp5
=====================================
lsphp is my webserver (litespeed). The sleeping processes are my SHOUTcast servers.
The thing I am concerned about is the "94.3%ni". This is slowing down my server completely and I am not too sure of what it is. Can anyone shed any light on this?
My VPS holds about 80 domains and low-use accounts.
Every night, from around 1.30am, the load suddenly skyrockets and will usually be around 5 to 10 for a few hours. Occasionally it'll spike to 30+ for a few minutes.
I had some antispam software running, and a couple of other packages (mail queues, mail manage etc), so I disabled all of that and removed all the crontab entries etc.
It's not really made any difference.
I can see the load stats going back 8 hours, as part of the ASSP spam package (I've just left the ASSP server load cron running just so I can continue monitoring it!)
Can the apparent load on my VPS be caused by other VPS's on the same node?? So in reality, my load is fine but is being affected by other people's VPS's?
I hope that makes sense. I'm 99% sure that my VPS is 'clean' (in so far as cron entries)
I'm asking the question because I took a second VPS on the same node and that one too has high loads overnight when there's nothing running on it (ie, no add-on software, no Cpanel accounts added)
I have a VPS with LXadmin control panel and 1024 Ram.
the memory always 333-450 but now it is more than 800 and the VPS stopped I restarted it many times but after restarting it the memory gone crazy again.
So, how to know what causes high load and eating my Memory?
Anyone know of any good/cheap high-bandwidth VPS providers? Don't need anything crazy as far as processing power or RAM (512MB with no burstable is fine). Sorta like Slicebox's budget servers, which I've had good experience with.
To e upfront, the box will be used for a little bit of testing, etc. but mostly to seed the latest Windows 7 builds :p. Don't think Microsoft minds all that much...Win7 requires a legitimate beta key to activate (which I have, and I'm not giving anyone mine) and it's a whole lot cheap for them to let people download over BitTorrent than Akamai, which they normally use.
So, any ideas? EU isn't out of the question...anywhere with a lot of/unmetered bandwidth for cheap, and a VPS that's reliable + has at least 512MB of memory for prices comparable (or slightly lower than) to Slicebox.
I've a remote download site that uses tons of BW (about 900GB daily), and it uses sql connection quite alot - I've set it to max connection for my current server.
For now, I've the intention of separating main site with download server. where The main site will contains the sql DB. But my concern is, I want to buy a cheap VPS for the main site, but no idea if I need high BW and ram.
I've got a dedicated with LW.
I've had it for a while and during that time I've never seen the swap memory go over 20%.
A month or so ago, I had the server upgraded to 8GB of ram to make room for more planned sites.
Since then, the swap memory has gone rampant. It regulary goes to 93% used with less than 20% of the regular ram and really no load on the server.
I've contacted support twice about it and was told don't worry it's normal.
From what I've read in the cpanel forum, no it's not normal and may in fact be caused by bad ram chips and if it hits 100% could freeze the server.
There are no processes or users causing it, so It's something else.
Has anybody had this type of problem that they resolved and could share what they did to resolve it?
